Gravity: I2C 4-20mA DAC - 2-kanałowy konwerter DAC 4-20mA

The Adafruit 5974 module with the HX711 converter enables precise reading of signals from strain gauges and load cells based on a Wheatstone bridge, offering 24-bit resolution and selectable gain. With an integrated screw terminal and options for sampling rate and channel configuration, it is used in projects involving force, pressure, or weight measurement in IoT systems, electronic scales, and mechanical testing.

3-channel voltage and current monitoring module designed to work with the Raspberry Pi. It can measure voltage ranging from 0 to 26 V and voltage ± 3.2 A. SB Components 20805

Module with 16-bit AD5693R DAC converter with built-in EEPROM memory. Equipped with a STEMMA QT connector, it communicates using the I2C bus. Adafruit 5811

Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553

A 16-bit DAC converter module designed to work with M5Stack sets. It enables the conversion of analog signals into a digital signal. M5Stack ADC Unit

Gravity module designed based on the GP8211 system. It is a single-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with a resolution of 15-bit and an accuracy of 0.01%. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1071

DFRobot DFR1184 module with a 15-bit ADS1115 converter enables precise voltage measurements of 0–10 V from industrial sensors. The dual-channel design, support for I2C/UART, and compatibility with popular platforms make it an effective solution for automation systems, environmental monitoring, and energy management.

Gravity: I2C 12-Bit DAC is a module with 12-bit DAC and built-in EEPROM memory. The module is powered by 3.3 ... 5V for communication used by the I2C interface. DFRobot DFR0552

A module with a stereo DAC converter based on the UDA1334A chip. It can generate a signal with a resolution of 16, 20 or 24 bits. It communicates via the I2S interface. Adafruit 4037

High-quality digital-to-analog converter that allows for pure stereo audio playback without the need for I2C configuration or the MCLK pin. It supports I2S signals (BCLK, WSEL, DIN) and audio formats up to 32 bits and 384 kHz, providing an excellent signal-to-noise ratio (110 dB). Audio output is available via a 3.5 mm jack or on-board pads, and the module works best as a line output to amplifiers and audio systems. Adafruit 6251

Module with 12-bit DAC converter and built-in EEPROM memory. The module is supplied with the voltage from 2.7 to 5.5V, the I2C interface is used for communication. SparkFun BOB-12918

Gravity module designed based on the GP8101S system. It is a single-channel DAC (analog-to-digital) converter with PWM communication that offers an output signal with 8-bit resolution and 0.2% accuracy. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1036

Module with 4-channel ADC ADS1015 converter. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 1083

Module with 8 inputs for data acquisition from 0-24 mA analog current inputs. It communicates via RS485 interface and supports Modbus RTU protocol. The board is enclosed in an industrial enclosure. GM1008

Gravity module designed based on the GP8503 system. It is a two-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with 12-bit resolution and 0.1% accuracy. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1034

Gravity module designed based on the GP8512 system. It is a single-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with a resolution of 15-bit and an accuracy of 0.01%. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1035