Load Cell Amplifier - a module for a pressure sensor with an ADC HX711 converter
ID: 562514
5906623417698
zł54.45
Tax included
zł44.27 tax excl.
A module with a 24-bit ADC converter HX711, which allows you to read data from strain gauges and scales. It communicates via the serial interface. SparkFun SEN-13879
Description
A module with a 24-bit ADC converter HX711, which allows you to read data from strain gauges and scales. It has a built-in programmable low-noise amplifier with optional gain of 32, 64 and 128. The HX711 chip integrates the power circuit, built-in clock oscillator and other peripheral circuits with fast response and noise immunity.
The load cells use a Wheatstone four-wire bridge configuration to connect to the HX711. These are RED, BLK, WHT, GRN and YLW colors, each of which corresponds to an encoding:
- Red - excitation + or VCC
- Black - excitation- or GND
- White - amplifier, signal or output
- Green - A +, S + or O +
- Yellow - screen
The YLW pin acts as an optional input that is not connected to a strain gauge, but is used for grounding and shielding against external electromagnetic interference (EMI).
The module communicates via the serial interface and is supplied with the voltage from 2.7 V to 5 V. Full documentation with examples of use is available on the product page.
Features
- 24-bit ADC converter
- Programmable gain: 32 dB for channel B, 64 dB or 128 dB for channel A
- 10 SPS or 80 SPS output data baud rate
- Supply voltage: 2.7 V to 5 V
- Current consumption: 1.5 mA
- Dimensions: 23 x 31 mm
562514
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
ADC converter module with 7 measurement channels (measuring 0-5V, 0-10V voltage and 4-20 mA current). Communicates via RS485 industrial interface using Modbus RTU protocol. R4AVA07
zł40.52
4 weeks
No product available!
Module with 8-bit ADC and 8-bit DAC. It allows you to measure voltage and generate an analog signal. Communicates via I2C
zł6.42
4 weeks
No product available!
Module with 4-channel ADC ADS1015 converter. The system enables analog voltage conversion for single signals and differential signals with 12-bit resolution. I2C communication
zł18.52
24h
Available quantity: 2
Available
Gravity: I2C 12-Bit DAC is a module with 12-bit DAC and built-in EEPROM memory. The module is powered by 3.3 ... 5V for communication used by the I2C interface. DFRobot DFR0552
zł21.81
24h
Available quantity: 3
Available
Gravity module designed based on the GP8503 system. It is a two-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with 12-bit resolution and 0.1% accuracy. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1034
zł47.24
24h
Available quantity: 3
Available
Dual-channel ADC converter compatible with the SYZYGY standard. The module can simultaneously obtain two 25V signals with 14-bit resolution and sampling frequency up to 100MS/s. The module is compatible with Eclypse Z7 and Genesys ZU evaluation kits. Digilent Zmod Scope 1410-105 (410-396)
zł1,344.41
3 weeks
No product available!
Gravity module designed based on the GP8413 system. It is a two-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with a resolution of 15-bit and an accuracy of 0.2%. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1073
zł59.24
24h
Available quantity: 2
Available
DAC converter module with current output in the range of 0 to 25 mA. It is powered by 18 V to 24 V and communicates via I2C interface (Gravity connector). It is used as a controller in industrial applications. DFRobot DFR0972
zł50.28
24h
Available quantity: 5
Available
A module with a stereo DAC converter based on the UDA1334A chip. It can generate a signal with a resolution of 16, 20 or 24 bits. It communicates via the I2S interface. Adafruit 4037
zł70.16
4 weeks
No product available!
Audio expansion module with CS4344 24-bit DAC converter. Numato Lab EXPAUD002
zł107.19
3 weeks
No product available!
A 16-bit DAC converter module designed to work with M5Stack sets. It enables the conversion of analog signals into a digital signal. M5Stack ADC Unit
zł31.89
24h
Available quantity: 9
Available
A 2-channel DAC converter module with an output voltage range from 0 to 10 V. It is powered by 3.3 V to 5 V and communicates via I2C interface (Gravity connector). It is used as a controller in industrial applications. DFRobot DFR0971
zł49.90
24h
Available quantity: 5
Available
Module with 4-channel ADC ADS1015 converter. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 1083
zł50.28
24h
Available quantity: 6
Available
Extension module with ADC AD7616 converter dedicated to FPGA boards. It offers 32 channels with a resolution of 16 bits and an FMC LPC connector. Numato Lab NLFMCADC002
zł6,195.01
3 weeks
No product available!
Module with 24-bit ADC NAU7802 converter. It enables reading data from strain gauges and scales. I2C interface. SparkFun SEN-15242
zł95.92
24h
Available quantity: 5
Available
A module with a 24-bit differential ADC NAU7802 optimized for reading strain gauges in a Wheatstone bridge configuration. It offers high precision force or mass measurements. Thanks to the I2C interface, ready-made libraries and screw connectors, it is easy to integrate, especially in mobile and DIY projects. Adafruit 4538
zł30.33
24h
Available quantity: 1
Available
A module with a 24-bit ADC converter HX711, which allows you to read data from strain gauges and scales. It communicates via the serial interface. SparkFun SEN-13879