Adafruit Feather nRF52840 Express - bluetooth low energy module

Adafruit Feather 328P is a module with a built-in ATmega 328P AVR microcontroller (8MHz, 32kB Flash, 2kB RAM). The board is compatible with Arduino IDE, has small dimensions and low weight, and the built-in USB connector allows programming and debugging. Adafruit 3458

At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip. Adafruit 3179

Module with WiFi Espressif ESP32-S2. It integrates two 3.3 V stabilizers, SPI Flash memory, LiPo charging circuit, light sensor and RGB diode. It is equipped with a STEMMA QT connector. Adafruit 4769

Development kit with SAMD21G18 microcontroller with ARM Cortex M0 core and LoRa RFM95 868/915 MHz radio communication module. Adafruit 3178

The board is equipped with ATSAME51 microcontroller (ARM Cortex-M core) with CAN bus and SPI Flash memory, GPIO pins and a connector for connecting the battery with the charging circuit. Adafruit 4759

Development board with ESP8266 microcontroller with built-in Wi-Fi communication. The system is clocked at 80 MHz and powered by 3.3 V. It includes a Tensillica core and a full Wi-Fi stack. Adafruit 3046

Module with WiFi Espressif ESP32-S2. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5000

A board with an RP2040 microcontroller and a LoRa RF95 module operating in the 868 MHz frequency band. It has a built-in LiPo charging circuit and STEMMA QT connector. Ideal for IoT projects. Adafruit 5714

Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5477

A modern development board in the Feather format, equipped with a dual-core Raspberry Pi RP2350 Cortex M33 microcontroller clocked at 150 MHz and 8 MB of PSRAM, ideal for advanced IoT projects and Micropython/CircuitPython applications. The board offers a wide range of ports, including an HSTX 22-pin connector, USB-C with bootloader, and STEMMA QT, as well as numerous GPIOs and an integrated LiPo battery charger, combining high performance with convenience of use. Adafruit 6130

Module with ATmega32u4 microcontroller and 900 MHz wireless transceiver. The module can be used for transmission in the ISM 868 MHz band after the appropriate software configuration. The microcontroller is clocked at 8 MHz and works at 3.3 V. Adafruit 3076

Development kit with nRF52832 microcontroller with ARM Cortex M4F core. Equipped with 512KB Flash and 64KB SRAM, it can support Bluetooth (BLE) communication. Adafruit 3406

Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5323

Low-power, 2.4GHz spectrum wireless protocol that you can use with iOS without needing special certification. Supported by all modern smart phones - excellent for use in portable projects that will make use of an iOS or Android phone or tablet; it also is supported in Mac OS X and Windows 8+. Adafruit 2995

The board is equipped with the ATSAMD51J19 microcontroller with ARM Cortex-M4 core and SPI Flash memory, GPIO pins, connector for connecting the battery with the charging circuit. Adafruit 3857

Adafruit Feather M0 WiFi - ATSAMD21 + ATWINC1500 is a development board with a 32-bit ATSAMD21G18 microcontroller based on Cortex-M0 core. The board also has an ATWINC1500 module that provides WiFi connectivity. Adafruit 3010