

J-Link RX Adapter, RoHS, Segger
The J-Link RX Adapter allows JTAG connections between J-Link and target hardware which comes with the Renesas RX600 series MCUs.
The J-Link RX adapter is able to optionally power the connected target hardware.
3.3V or 5V supply voltage can be selected using a Jumper. The target is supplied via the VTref connection when the supply option is jumpered.
Code: J-Link RX Adapter (8.06.01)
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
J-LINK EDU Mini is a version of the J-Link EDU (8.08.90) in a reduced form factor with identical functionality for Cortex-M based targets. It has been designed to allow students and educational facilities as well as hobbyists access to top of the line debug probe technology. Version for non-commercial use only. J-Link EDU mini
A device that provides electrical isolation between the J-Trace emulator and the ARM board, which protects against electrical interference, especially in systems where the development tools and the application do not share the same ground. It provides 1 kV DC isolation, supports trace frequencies up to 75 MHz, and is compatible with J-Trace V2 and later versions, with a minimum power consumption of 25 µA. Segger J-Trace Isolator (07/08/10)
J-Link SDK one year Support and Update Agreement extension. Can only be purchased by customers with a J-Link SDK License (Model 8.08.06). Segger J-Link SDK Extension (8.08.18)
No product available!
A set of three BGA adapters enables easy testing and programming of flash devices in these packages, eliminating the need for dedicated solutions for each form factor. The adapters are compatible with the SEGGER (Q)SPI Flash Evaluator and other test systems, making them a versatile tool for both test and production. SEGGER (Q)SPI Flash Evaluator Adapter board Pack for BGA (6.40.02)
No product available!
A power adapter that provides a stabilized supply voltage to the target board (can be adjusted from 3.6V to 0.8V). Segger Target Supply Adapter (8.06.18)
The Segger J-Link Microchip Adapter (8/06/09) provides a debug connection between a J-Link probe and hardware with Microchip PIC32 series microcontrollers. Supports RJ12 debug connector, 14-pin MIPS connector and 6-pin PICkit connector.
Adapter providing two dedicated supply voltages - for programming and powering for the target board. Useful for programming modules that do not support low voltage programming or require a voltage other than 5V. Segger Programming Voltage Adapter (8.06.30)
No product available!
The Segger J-Link Measurement+Patch Adapter allows you to easily customize connections between J-Link or Flasher devices and boards that do not have a standard debug connector. It is equipped with colored wires for signal identification, test points and jumpers for adjusting the voltages on the pins.
No product available!
A 1:1 adapter that allows you to connect a standard 20-pin connector to its 2mm pitch counterpart without any additional configuration. For some models, such as the J-Link PRO, pins 14, 16, 18 and 20 may not be connected to ground, so it is recommended to leave them unconnected on the target hardware. Segger 2mm Adapter (06/08/11)
No product available!
Adapter that converts standard 20-pin 2.54 mm connector to SWIM connector and 10-pin connector. Used for programming STM8 chips. Segger STM8 Adapter (8.06.22)
No product available!
An adapter that allows you to connect a 20-pin 0.1" connector to a 10-pin connector, allowing you to easily connect J-Link or Flasher programmers to your PCB using through-wires. It is ideal for prototyping, testing new designs and working with ST Discovery boards, offering flexibility, speed and time savings when making design changes.Segger Flying Wire Adapter (06.08.27)
No product available!
Power adapter providing a stabilized 5V supply voltage for the target board. Segger 5V Target Supply Adapter (8.06.29)
No product available!
The Segger J-Link Supply Adapter (8.06.14) allows you to manually set the debug probe I/O voltage, preventing damage to the target board, adjustable from 1.2V to 5.0V. It can be inserted between J-Link or Flasher and the target device, reducing the number of connections needed, which is especially useful in a production environment.
RS232 module used as a communication extension equipped with a female DSUB9 connector, allowing easy connection to a PC or USB-RS232 adapter. Segger emPower RS232 Add-On (6.32.32)
No product available!
AVR PDI adapter from standard 2.54mm 20 pin connector to 2.54mm 6 pin, 1.27mm 6 pin or 2.54mm 10 pin AVR PDI connector. Segger AVR PDI Adapter (8.06.26)
No product available!
No product available!
Adapter that enables JTAG connection between Flasher programmer and target hardware with Power Architecture or PowerPC microcontrollers. Converts 20-pin 0.1\'\' connector to 14-pin JTAG, ensuring compatibility, stability and secure connection. Segger PPC 14-Pin Adapter (06.08.07)
No product available!
J-Link RX Adapter, RoHS, Segger