New products
New products New products
Best sellers
There are 16645 products.
A modern laser scanner that integrates the advantages of triangulation and DTOF. It offers a measuring range of up to 12 meters with a low dead zone of 5 cm. The scanning frequency is 10 Hz (600 rpm) and the sampling rate is 5000, which allows an angular resolution of 0.72° to be achieved. Waveshare RPLIDAR C1
This Bluetooth Audio receiver module includes a USB port and TF card slot. With a pre-amp output, you can drive headphones or a 3W speaker directly. You can also add an active power amplifier and connect a loudspeaker. The module supports MP3, WMA, WAV and lossless FLAC audio formats. DFRobot TEL0108
Ultra small Dual DC motor driver for some room limited projects. UVLO (Under Voltage Latch-Out) features a safe guard for your system. DRI0041
Adafruit module with Si7021 temperature and humidity sensor. Sensor Sillicon Labs can measure temperature in the range of -10 ~ 125 ° C, and humidity in the range of 0-100 & RH. The sensor communicates using the I2C interface. Adafruit 3251
A compact development board that uses the ESP32-PICO-MINI chip. It provides wireless communication via Bluetooth and serves as an easy-to-configure UART converter. It has a built-in PCB antenna. SparkFun WRL-24113
RF module providing wireless communication compliant with the IEEE 802.15.4 standard. They operate in the 2.4 GHz ISM band and enable local configuration via BLE with the Digi XBee mobile application. They are equipped with the Silicon Labs EFR32MG SoC transmitter and receiver chipset. The range in buildings is up to 90 m, while in open space it reaches up to 3200 m. SparkFun WRL-22631
An adapter that allows you to connect modules in the XBee format to a computer via the USB Type-C interface. The adapter is based on the FT231XS system. SparkFun WRL-22043
Base board for prototyping IoT applications using the new Digi XBee 3 Low-Power LTE-M/NB-IoT and Digi XBee RR modules. It gives access to the full functionality of the XBee module pins, including two USB Type-C connectors for UART communication and firmware updates, a Qwiic connector for I2C-compatible sensors and peripherals. SparkFun WRL-21636
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 9.96:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter.
A base board that allows you to integrate modern Digi XBee 3 and Digi XBee RR Pro modules with the Arduino format, enabling you to build wireless projects. It uses a USB Type-C connector and a Qwiic connector to connect I2C sensors. SparkFun WRL-22131
Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900MHz to the Internet or your mobile device. Adafruit 3230
Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 3191
EMMC Flash memory module for Hardkernel Odroid N2 computers. 32GB capacity, Android operating system installed. The set includes a microSD adapter. Hardkernel 32GB eMMC Module N2 Android
A module with a 24-bit ADC converter HX711, which allows you to read data from strain gauges and scales. It communicates via the serial interface. SparkFun SEN-13879
U-shaped Bracket Kit for Dual-Axis Servomechanisms is a ready-made base for constructing rotating modules in electronic and robotic projects. It facilitates the creation of tracking systems, camera modules, and other setups requiring precise movement in two planes. Thanks to simple assembly and broad compatibility, it is ideally suited for educational and prototyping applications.
pH electrode for industrial and laboratory applications. Made of a sensitive, low-impedance glass membrane, it guarantees fast response time and excellent thermal stability. DFRobot FIT0348
Module with the STM32F746IGT6 microcontroller, including a base board and accessories. Waveshare Open746I-C Standard
A servo with standard sizes. At 6 V, it can generate a torque of up to 15.5 kg*cm. Additionally equipped with a potentiometer informing about the servo position. It has a standard 3-pin connector matching most popular modeling controllers and an additional servo position pin.
Soldering station 2 in 1 for hot air and arrowhead. With original Japanese heating elements Hakko and PID controller correcting the temperature on an ongoing basis.