New products
New products New products
Best sellers
There are 16641 products.
OS Preinstalled Flash Memory with Android
Camera with a resolution of 8 MPx with a USB interface. Equipped with a CMOS IMX219 sensor with a lens with a viewing angle of 60° and an autofocus function. ArduCAM B0292
Prototype board designed to cooperate with Particle Photon. The board has prototype holes with a 2.54 mm pitch and pins of the I2C interface. SparkFun DEV-13598
Camera with OV4689 CMOS sensor with a resolution of 2688x1520 px. It communicates via a parallel interface. ArduCAM U6035
Miniature camera module with OV5647 5MP sensor dedicated to Raspberry Pi Zero and Compute Module. Equipped with a lens with a viewing angle of 160°. ArduCAM B006605
Camera module 8 MPx with IMX219 sensor and lens with a viewing angle of 77°. To be used as a replacement on the RPI Camera Board V2. ArduCAM B0190
Expander (shield) compatible with Arduino and NUCLEO (STM32) systems, equipped with a Bluetooth 4.1 (BLE) radio module from the SPBTLE-RF family
This disc load cell (sometimes called a strain gauge) can translate up to a whopping 200kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the disc. SEN-13332
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0 + cores, which operate at a frequency of 133 MHz and 264 kB RAM. The additional ESP8285 system allows communication in the WiFi network. Seeed Studio 102991555
Module with a 3-color e-Paper display with a diagonal of 4.2" and a resolution of 400x300 px. Communication via the SPI interface. Waveshare Pico-ePaper-4.2-B
Module with 7-color ACeP e-Paper display, 5.65" diagonal and 600x448 px resolution. Communication via SPI interface. Waveshare Pico-ePaper-5.65
32-bit microcontroller from the STM32F7 family with ARM Cortex-M7 core, 512kB Flash memory, 320kB SRAM, I2C, SPI, UART / USART memory, USB, CAN, 1.7 ... 3.6V, 144LQFP, STM, RoHS
X-NUCLEO-IDS01A4 is a development board STM32 Nucleo that allows the use of the RF SPSGRF-868 module for the ISM band (868 MHz carrier).
This compact board breaks out the pins of a microSD card connector necessary to interface with the card through SPI (Serial Peripheral Interface), and it can be directly integrated into 5 V systems thanks to its on board 3.3 V regulator and level shifting circuity. Pololu 2587
This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. This unit works great from 5 to 12V (datasheet shows 12V). You can also install a jumper wire past the 5V regulator on board to make this unit work at 3.3V. Sensor uses 1.6mA@3.3V. SEN-13285
Camera module based on the CMOS MT9V022 matrix with a resolution of 752x480 px (0.36 MPx). Designed for use with ArduCAM USB Shield. ArduCAM B0109
The driver with the TPIC6C596 system allows you to control 7-segment displays using three signal lines. Serial connection of controllers is possible. SparkFun WIG-13279
Case for the MacroPad RP2040 mechanical keyboard. The set includes accessories and non-slip feet. Adafruit 5103
This level shifter board contains 3 x TSX0108E bi-directional level shifter ICs. The 30-pin and 12-pin GPIO ports on the XU4 are converted to the more common 0.1inch (2.54mm) pitch 40-pin header. All the signals can be level shifted to 3.3V or 5V.
Set with a monochrome camera with a resolution of 0.3 MPx with an OV7251 sensor and a USB 2.0 adapter. ArduCAM EK021