Best sellers

Unshielded UTP category 5E Ethernet network cable with RJ45 plugs. Lanberg PCU5-10CC-0300-Y

Oscilloscope probe designed to analyze signals generated by the ignition coil in car engines. It is compatible with most digital oscilloscopes. Hantek HT25COP

Screwdriver set with 38 bits for precise work. The screwdriver has interchangeable bits, so you can adjust the size to the size of the thread.

Universal oscilloscope probe with BNC plug and 10:1 voltage divider. It has a frequency range of 60 MHz and allows you to perform measurements with a maximum voltage of up to 600 V.

Panel PWM generator that allows precise regulation of the PWM signal in a wide frequency range from 1 Hz to 150 kHz. It is powered with a voltage in the range of 3.3 V to 30 V via a screw connector. XY-PWM

JTAG / SWD programmer-debugger with USB and WiFi interface. It supports microcontrollers and microprocessors with Cortex-M, Cortex-A, Cortex-R and ARM7, ARM9 and ARM11 cores of most manufacturers as well as 8051, RISC-V, PIC32, RX. Segger J-Link WiFi (8.14.28)

Adafruit Universal Thermocouple Amplifier MAX31856 is an amplifier module for thermocouples. It was based on the MAX31856 chip. The module is fitted with K, J, N, R, S, T, E or B thermocouples. The SPI interface is used for communication. Adafruit 3263

The FX2N-06MT PLC controller module has 4 input points and 2 transistor output points with a maximum current of 1A. The device enables fast counting up to 2/3K.

60W soldering iron with tip temperature regulator placed in the handle. It has temperature control from 100°C to 400°C. Elwik LERT-24

Expansion board for STM32 Nucleo enabling output support in the industry standard. It allows you to control eight galvanically isolated outputs as relays. It has a connector compatible with Arduino® UNO R3. STMicroelectronics X-NUCLEO-OUT02A1

The FX2N-20MT-TTL PLC module supports 12 input points and 8 relay outputs with a maximum current of 1A at 24V DC. Enables fast counting up to 2/3K, optional analog inputs.

Pin expander for Raspberry Pi Pico boards. It is equipped with a standard female connector and two sets of 2x20 pin male strips. SB Components 20836

IPS 5.5" LCD display with a touch panel dedicated to Raspberry Pi minicomputers. Equipped with an HDMI interface for displaying the image and USB for the touch panel. It has a resolution of 1440x2560 pixels. Waveshare 5.5inch 1440x2560 LCD

Shielded FTP category 6 Ethernet network cable with RJ45 plugs. Lanberg PCF6-10CC-0300-Y

Ultrasonic distance sensor determines the distance to a target by measuring time lapses between the sending and receiving of the ultrasonic pulse. This ME007YS Waterproof Ultrasonic Sensor features high accuracy, steady data output and a certain penetration power(smog, dust). SEN0312

Tip GD-3 No. 053 mounted on the heater. Suitable for all types of Elwik soldering irons.

Module with ENS160 gas sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C or SPI interface. Adafruit 5606

Module with a differential pressure sensor based on the MPXV5010DP system. It uses a 22-bit ADC and allows the measurement of the pressure difference between two inlets in the range of up to 10 kPa. Comes with a soldered Raspberry Pi Pico W board. SB Components 26173

4-color e-Paper display with a diagonal of 2.36" and a resolution of 296x168 px. Communicates via the SPI interface. Waveshare 2.36inch e-Paper (G)

Shielded FTP category 6 Ethernet network cable with RJ45 plugs. Lanberg PCF6-10CC-0500-G