Best sellers
There are 16531 products.
ABS filament in yellow with a diameter of 1.75 mm. 0.85 kg of filament is wound on a spool. Fiberlogy ABS Yellow
The S9V11MACMA switching step-up/step-down regulator efficiently produces a finely adjustable output between 2.5 V and 9 V whether it is higher or lower than the input voltage, which can range from 3 V to 16 V. The regulator also has a precision-adjustable low-voltage cutoff with hysteresis that can be used to prevent battery over-discharge.
ABS filament in gray with a diameter of 1.75 mm. 0.85 kg of filament is wound on a spool. Fiberlogy ABS Gray
The S9V11F5S6CMA switching step-up/step-down regulator efficiently produces a fixed 5 V (default) or 6 V (selectable) output whether it is higher or lower than the input voltage, which can range from 2 V to 16 V. (Note: minimum start-up voltage is 3 V, but it operates to 2 V after that.)
ABS filament in graphite with a diameter of 1.75 mm. 0.85 kg of filament is wound on a spool. Fiberlogy ABS Graphite
ARK terminal connector spring 3-pin, pitch 2.54 mm, non-detachable.
Audio preamplifier based on NE5532 chips. Equipped with an input selector function. Display and remote control included
ABS filament in blue with a diameter of 1.75 mm. 0.85 kg of filament is wound on a spool. Fiberlogy ABS Blue
LPCXpresso55S28 evaluation kit with LPC55S28 microcontroller with ARM Cortex-M33 core. The board contains a built-in LPC-Link2 programmer, audio subsystem, accelerometer, microSD slot, USB interfaces and expansion connectors. NXP LPC55S28-EVK
These lightweight aluminum brackets make it easy to mount and integrate the Sharp GP2Y0A02, GP2Y0A21, and GP2Y0A41 Distance Sensors into your project. The brackets are strong enough to hold their position, but they can also be bent by hand to different angles if the application calls for it.
Prototype board designed to cooperate with Particle Photon. The board has prototype holes with a 2.54 mm pitch and pins of the I2C interface. SparkFun DEV-13598
Particle’s IoT (Internet of Things) hardware development kit, the Photon, provides everything you need to build a connected project. Particle has combined a powerful 120Mhz ARM Cortex M3 micro-controller with a Broadcom Wi-Fi chip in a tiny thumbnail-sized module called the PØ (P-Zero)
Tiny (18 x 44 mm) breadboard-friendly development board, easy to use, hacker friendly. ATmega328 brains32KB of flash (1/2 K is reserved for the bootloader), 2KB of RAM, clocked at 16MHz. Adafruit 2590
Easy PLA filament in Vertigo, 1.75 mm in diameter. 0.85 kg of filament is wound on a spool. Fiberlogy Easy PLA Vertigo
Vertical Grove socket for through-hole mounting, 4-pin, pitch 2.0 mm. Set of 10 pieces. Seeed Studio 110990030
Yellow mounting for Grove modules, which ensure convenient installation and replacement of modules in the project. Compatible with LEGO. Set of 4. Seeed Studio 110070025
8-channel I2C expander module based on the TCA9548A system. The module has Qwiic connectors and allows communication with many I2C devices that have the same address. Sparkfun BOB-16784
4-pin speaker socket with two banana connectors. Rectangular, dimensions 92 x 80 mm
A pair of 4-pin curved magnetic connectors. It has a 2.2 mm pitch and can conduct a current of 3 A
This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. This unit works great from 5 to 12V (datasheet shows 12V). You can also install a jumper wire past the 5V regulator on board to make this unit work at 3.3V. Sensor uses 1.6mA@3.3V. SEN-13285