Best sellers
There are 17620 products.
Low Energy Bluetooth adapter module with USB 2.0 connector. allows communication with BLE devices
Programmable wireless BT4.0 transmitter, compatible with sensors of the iNode Care Sensor series. It allows you to enable / disable other devices, eg after exceeding the set temperature or humidity, moving the sensor or changing its position. Allows you to control directly from your smartphone, tablet or computer
5 MP camera module with OV5647 sensor for Raspberry Pi with MIPI CSI-2 interface (including Raspberry Pi 5, 4B, 3B+, 3A+, Zero, Zero 2W), focal length 3.6 mm, field of view 50°, manual focus adjustment, IR illumination for low-light operation. Waveshare RPi Camera (F)
El-wire is a thin and flexible wire which shines under high voltage. The cable is red, has a diameter of 3mm and a length of 3 meters
Gravity: Heart Rate Monitor Sensor is a sensor used to measure heart activity. Adapted for easy use with Arduino. SparkFun SEN0213
At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much). Adafruit 2796
Switching power supply from MEAN WELL, power 40W, output voltage 12VDC and output current 3.33A. Mounting on a DIN rail. Built-in overload and short-circuit protection. MDR-40-12
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 9.96:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter.
X-NUCLEO-IDS01A4 is a development board STM32 Nucleo that allows the use of the RF SPSGRF-868 module for the ISM band (868 MHz carrier).
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 248.98:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
Precise electronic balance with a measuring range of up to 300 g. It enables measurement with an accuracy of 0.01 g
32-bit microcontroller from the STM32F7 family with ARM Cortex-M7 core, 512kB Flash memory, 320kB SRAM, I2C, SPI, UART / USART memory, USB, CAN, 1.7 ... 3.6V, 144LQFP, STM, RoHS
Base board compatible with Arduino. It was equipped with an ATmega328P microcontroller. It has 22 I / O lines (including 6 PWM channels) and 8 analog inputs and a Qwiic connector. SparkFun DEV-18158
Plotter with a laser with a power of 3000 mW and a beam length of 405 nm. It allows you to engrave in materials such as wood, plastics, rubber or thin leather. NEJE DK-8-KZ
Air speed sensor module based on the FS3000-1005 chip. The board is equipped with Qwiic connectors. SparkFun SEN-18377
2-channel converter for Raspberry Pi Pico that provides easy communication between UART TTL serial interface and RJ45 Ethernet. Waveshare Pico-ETH-CH9121
Qwiic adapter designed for micro:bit educational modules. Facilitates access to all pins that are led out on the connector with a pitch of 2.54 mm and the Qwiic connector. SparkFun BOB-16445