

The SparkFun BME280 Atmospheric Sensor Breakout is the easy way to measure barometric pressure, humidity, and temperature readings all without taking up too much space. Basically, anything you need to know about atmospheric conditions you can find out from this tiny breakout. The BME280 Breakout has been design to be used in indoor/outdoor navigation, weather forecasting, home automation, and even personal health and wellness monitoring.
The on-board BME280 sensor measures atmospheric pressure from 30kPa to 110kPa as well as relative humidity and temperature. The breakout provides a 3.3V SPI interface, a 5V tolerant I2C interface (with pull-up resistors to 3.3V), takes measurements at less than 1mA and idles less than 5µA. The BME280 Breakout board has 10 pins, but no more than six are used at a single time. The left side of the board provide power, ground, and I2C pins. The remaining pins which provide SPI functionality and have another power and ground, are broken out on the other side.
Note: The breakout does NOT have headers installed and will need to purchased and soldered on yourself.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The BME280 integrated circuit is a sensor of atmospheric conditions (pressure, humidity, temperature) in the SMD casing (2.5mmx2.5mm). The sensor has very low power consumption (average 3.6uA) and has an I2C / SPI bus. The Bosch Sensortec system
No product available!
Small 10 DoF IMU module with 3-axis gyroscope and accelerometer (LSM6DSO), 3-axis magnetometer (LIS3MDL) and barometer (LPS22DF). It is equipped with an I2C interface, a voltage stabilizer and a voltage level converter. Pololu 2863
Module with humidity and air temperature sensor based on the AM2302 system. It allows temperature measurement in the range from -40 to 80 ° C and the humidity measurement takes place in the range of 5 to 99% RH. The module has a connector in accordance with the Grove standard. Seeed Studio 101020019
Module with a digital temperature and humidity sensor based on the SHT31-F system. Communication via the I2C interface. Equipped with a Gravity DFRobot SEN0334 connector
Wireless sensor with LoRaWAN network communication. Dedicated to industrial long-distance data acquisition with a wide measurement range of temperature from -40°C to 85°C and humidity from 0 to 100% RH. Seeed Studio 114992867
I2C BME680 Environmental Sensor is a gas, pressure, temperature and humidity sensor in one MEMS housing. The module is supplied with 3.3-5V, for communication the I2C or SPI interface is used. DFRobot SEN0248
Digital temperature and humidity sensor with calibrated digital output signal. Equipped with a 2.5 mm 4-pin male stereo audio connector that works perfectly with the Sonoff TH10/TH16 socket. Sonoff Si7021
Module with DHT20 sensor. It allows you to measure humidity in the range from 0 to 100% and temperature from -40 to 80 ℃. Seeed Studio 101020932
Module with BME280 environmental sensor. It allows you to measure temperature, humidity and pressure. The sensor is equipped with two communication interfaces: SPI and I2C. SparkFun SEN-13905
No product available!
Module with a temperature and humidity sensor DHT22. It allows you to measure humidity in the range from 0 to 100% and temperature from -40 to 80℃. DFRobot SEN0137
Module with a pressure, temperature and humidity sensor based on the MS8607. Equipped with a STEMMA QT connector, it communicates via the I2C. Adafruit 4716
Module with a digital temperature and humidity sensor based on the SHT31-F system. Communication via the I2C interface. DFRobot SEN0332
relative humidity sensor with integrated temperature sensor for highly accurate measurements at low power. With the TI HDC1080, you can determine the relative humidity of the environment with up to 14 bits of resolution. Digilent 410-347
No product available!
Air humidity and temperature sensor with 1-Wire interface.
Temperature and humidity sensor SHT10 with a stainless probe. Provides high temperature and pressure resistance. DFRobot SEN0148
A digital temperature and humidity sensor module based on the SHT41 chip. It features a STEMMA QT/Qwiic connector and communicates via an I2C interface. Adafruit 5776
Ideal for environmental sensing and data logging and perfect for build a weather stations or humidor control system; built-in 4.7KΩ pullup resistors for I2C communications. SEN-13763
SEN-13676