SparkFun WiFi Shield
ID: 561003
zł95.23
Tax included
zł77.42 tax excl.
Arduino compatible shield for the ESP8266 WiFi SoC – a leading platform for Internet of Things (IoT) or WiFi-related projects. WRL-13287
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
The SparkFun ESP8266 WiFi Shield is an Arduino compatible shield for the ESP8266 WiFi SoC – a leading platform for Internet of Things (IoT) or WiFi-related projects. There are a variety of designs based around the ESP8266, including tiny, modular boards and more accessible development boards like our very own SparkFun ESP8266 Thing. The ESP8266 WiFi Shield finds a middle ground between the Module and the Thing that provides a great introduction to the ESP8266 – without leaving the comfortable hardware confines of your Arduino. If you just have an Arduino project that needs an inexpensive gateway to the Internet, the ESP8266 WiFi Shield does everything from turning on an LED to posting data with phant.io.
The ESP8266 WiFi Shield comes pre-flashed with an AT-command firmware, so it can be controlled by any UART, but it also breaks out and provides command access to all of the ESP8266’s I/O. Since this is an Arduino shield, it makes it easy to attach to any development board that utilizes the Arduino R3 layout. All it will take is a little soldering to attach the necessary headers. The ESP8266 is much more than a simple serial-to-WiFi gateway. It has almost a dozen I/O that can be configured as digital inputs or outputs – it even has an ADC! These GPIO are all broken out towards the top-left side of the shield. Additionally, the ESP8266 WiFi Shield can be repurposed and reprogrammed through the programming port found on the top-right side of the shield. Whether you want to add AT commands of your own, or flash custom firmware on the ESP8266, this port may come in very handy especially with it utilizing the pinout of our FTDI Basic breakouts.
This shield comes populated with all components as shown in the images and schematic; but it does not come with headers installed. We recommend the Arduino R3 Stackable Header Kit.
Features
- Arduino R3 Layout
- 802.11 b/g/n
- Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLLs, regulators, DCXO and power management units
- Integrated low power 32-bit CPU could be used as application processor
- +19.5dBm output power in 802.11b mode
561003
Data sheet
- Logic voltage
- 3,3 V
- Communication
- WiFi
- Wi-Fi chip
- ESP8266
- Wi-Fi standard
- 802.11 b/g/n
- Frequency range
- 2,4 GHz
- Baud rate
- 72,2 Mbps
- Antenna connector
- uFL
- Power supply voltage
- 5 V
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł113.90
24h
Available quantity: 70
Available
WiFi 802.11 b/g/n module with ESP8266 system, they have 22 edge terminals with 2 mm raster with the possibility of soldered gold connectors, 9 GPIO lines and 1 ADC line on the connector. Built-in PCB antenna. ESP-12E
zł10.25
24h
Available quantity: 136
Available
Development board with dimensions and spacing compatible with Arduino Uno R3. It have built-in Wi-Fi ESP8266 module. The device is compatible with WeDOS D1, it can be programmed from the level of Arduino IDE
zł25.90
24h
Available quantity: 3
Available
Other products in the same category (16)
Dragino LoRa Shield is an expansion board for Arduino (Uno, Leonardo, Mega, DUE) with a LoRa communication module (RFM98W system). Works at 433 MHz, maximum power up to 100 mW. In the set with the plate there is also an antenna. Seeed studio 113990194
zł142.26
6 weeks
No product available!
Module with Himax HM-01B0 camera and LoRa communication dedicated to Arduino Portenta H7 boards. Arduino ASX00026
zł489.00
3 weeks
No product available!
Ethernet network module with W5500 chip. It communicates via the SPI interface, it has a built-in TCP/IP stack. There are two Grove connectors with I2C and UART on the board. Seeed Studio 103030021
zł166.69
24h
Available quantity: 3
Available
Advanced expansion board for Arduino. It has support for mini-SIM cards and NB-IoT cards. Thanks to the GNSS module (Global Navigation Satellite System), it supports GPS, GLONASS, Galileo, QZSS and BeiDou GPS navigation systems. The module is powered by 7-12V voltage. DFRobot DFR0572
zł237.00
4 weeks
No product available!
Module with a radio receiver operating at 315 MHz for Arduino. DFRobot TEL0075
zł33.73
24h
Available quantity: 1
Available
Adafruit 789 - Adafruit PN532 NFC/RFID Controller Shield for Arduino + Extras
zł235.56
24h
Available quantity: 2
Available
Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.
zł99.00
24h
Available quantity: 39
Available
Board with the GNSS Cinterion TX62 module with support for Cat. M1 and NB IoT. Dedicated for Arduino Portenta H7. Arduino ASX00027
zł455.68
3 weeks
No product available!
The Arduino Ethernet Shield 2 allows an Arduino Board to connect to the internet. It is based on the Wiznet W5500 Ethernet chip. The Wiznet W5500 provides a network (IP) stack capable of both TCP and UDP. There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega
zł149.00
24h
Available quantity: 23
Available
UART-RS485 converter module. It enables communication of Arduino boards with industrial modules. DFRobot DFR0259
zł48.03
24h
Available quantity: 3
Available
A USB host module that contains all the digital logic and analog circuitry necessary to implement a USB peripheral or host controller using the SPI interface. SparkFun DEV-21247
zł209.00
6 weeks
No product available!
Module with Himax HM-01B0 camera and Ethernet communication dedicated to Arduino Portenta H7 boards. Arduino ASX00021
zł299.00
3 weeks
No product available!
Introducing Adafruit FONA 808 GSM + GPS Shield, an all-in-one cellular phone module with that lets you add location-tracking, voice, text, SMS and data to your project, in Arduino shield format for easy use. Adafruit 2636
zł326.70
4 weeks
No product available!
Expansion board with 4G/3G/2G communication module and GNSS positioning. The kit has pins compatible with Arduino and STM32 Nucleo. DFRobot TEL0124
zł359.23
4 weeks
No product available!
The Arduino expansion board is dedicated to applications that use NB-IoT communication. Thanks to the GNSS (Global Navigation Satellite System) module, it supports GPS, GLONASS, Galileo, QZSS and BeiDou navigation systems. The module is supplied with the voltage from 7 to 12 V. DFRobot DFR0572
zł245.31
24h
Available quantity: 1
Available
Ethernet network module with W5500 chip and PoE (Power over Ethernet) function. It communicates via the SPI interface, it has a built-in TCP/IP stack. DFRobot DFR0850
zł151.75
24h
Available quantity: 1
Available
Arduino compatible shield for the ESP8266 WiFi SoC – a leading platform for Internet of Things (IoT) or WiFi-related projects. WRL-13287