Shield Nucleo / Arduino with CAN and RS485 interfaces

Extension module for STM32 Nucleo based on a two-channel SIO transceiver and IO-Link PHY L6364Q with built-in voltage stabilizers and a DC-DC converter. STMicroelectronics X-NUCLEO-IOD02A1

The P-NUCLEO-IOD01A1 is an STM32 Nucleo pack composed of the NUCLEO-L073RZ development board, the STEVAL-IOD003V1 evaluation board and the X-NUCLEO-IKS01A2 expansion board

STM32 Nucleo-144 development board with STM32F446ZET6 MCU, supports Arduino, ST Zio and Morpho

NUCLEO series starter kit equipped with STM32G474RE microcontroller (512 kB Flash, Cortex-M4), with built-in programmer-debugger ST-Link-V3E, equipped with connectors compatible with Arduino.

The set consists of the STM32 NUCLEO-F401RE board with the STM32F401RE microcontroller and the X-NUCLEO-53L5A1 board with the VL53L5CX ToF distance sensor. STMicroelectronics P-NUCLEO-53L5A1

An expansion board with digital outputs (for industrial applications) designed to work with the STM32 Nucleo kits. The module is based on the IPS161HF double high-side switch. STMicroelectronics X-NUCLEO-OUT10A1

ToF VL53L7CX distance sensor expansion board with a 64-pixel array, a range of up to 3.5 m and a viewing angle of up to 90°. The overlay is compatible with STM32 Nucleo boards. STMicroelectronics X-NUCLEO-53L7A1

The X-NUCLEO-IHM16M1 motor driver expansion board is based on the STSPIN830 monolithic driver for three-phase brushless motors. It represents an affordable, easy-to-use solution for driving brushless motors in your STM32 Nucleo project, implementing single and three-shunt current sensing

Expansion board compatible with STM32 Nucleo. Allows you to prototype solutions with digital microphones. STMicroelectronics X-NUCLEO-CCA02M2

STM32 Nucleo-144 development board with STM32F207ZG MCU, supports Arduino, ST Zio and morpho connectivity

Starter kit from the NUCLEO series equipped with the STM32L452RE microcontroller (512 kB Flash, Cortex-M4), with a built-in programmer-debugger ST-Link/V2, equipped with connectors compatible with Arduino. STMicroelectronics NUCLEO-L452RE-P

The STEVAL-FKI433V2 evaluation board is based on the S2-LP sub-1GHz ultra-low power low data-rate transceiver suitable for ISM bands and wireless M-Bus. The NUCLEO-L053R8 motherboard is equipped with an STM32L0 low power microcontroller to control the S2-LP

NUCLEO series starter kit equipped with STM32G431RB microcontroller (128 kB Flash, Cortex-M4), with built-in programmer-debugger ST-Link-V3E, equipped with connectors compatible with Arduino.

The set consists of the STM32 NUCLEO-F401RE board with the STM32F401RE microcontroller and the X-NUCLEO-53L3A2 board with the VL53L3CX distance sensors operating in ToF technology. STMicroelectronics P-NUCLEO-53L3A2

KA-NUCLEO-F411CE v2 is a development board based on the STM32F411CE microcontroller. It has a built-in programmer compatible with ST-Link / v2-1, it is possible to program and debug the microcontroller via the USB connector.

Expansion board with BlueNRG-M0 module compatible with Bluetooth v4.2. It is compatible with the ST morpho connector system (unmounted) and Arduino UNO R3. Communication with the module is via the SPI interface. STMicroelectronics X-NUCLEO-IDB05A2