![Main view Main view](https://kamami.pl/80479-large_default/acs724-current-sensor-carrier-0a-to-20a.jpg)
![Main view Main view](https://kamami.pl/80479-large_default/acs724-current-sensor-carrier-0a-to-20a.jpg)
zł42.57 tax excl.
ACS724LLCTR-20AU current sensor module with a current measurement range from 0 to 20 A. It communicates via an analog interface. Pololu 4044
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
Module with a two-way Hall current sensor based on the ACS724LLCTR-20AU chip. It allows you to measure the current in the range from 0 to 20 A. The board is powered with the voltage from 4.5 V to 5.5 V and is intended for use in circuits with a logical voltage of 5 V. It offers a current path with low resistance (~ 1.2 mΩ) and electrical insulation up to 2.4 kV RMS. The output is a proportional analog voltage (200 mV/A) with offset 0.5 V and an error of ± 0,7%.
The sensor requires five connections to work properly: input current (IP+ and IP-), logic power (VCC and GND) and sensor output (OUT). Pin FILTER allows you to adjust the bandwidth of the plate by adding a capacitor to ground in parallel with the 1 nF capacitor that is already on the board. Without an additional external filter capacitor, the frequency response is approximately 90 kHz.
Data sheet
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
Module with ACHS-7123 current sensor with a measuring range of direct and alternating current from -30 to 30 A. It communicates via an analog interface. Pololu 4032
The module with a TA12-200 current sensor with a measuring range of alternating current up to 5 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020027
Module with ACHS-7121 current sensor with a measuring range of direct and alternating current from -10 to 10 A. It communicates via an analog interface. Pololu 4030
No product available!
Module with ACS724LLCTR-30AU current sensor with a measuring range of direct and alternating current from 0 to 30 A. It communicates via an analog interface. Pololu 4046
This board is a simple carrier of Broadcom’s bidirectional ±40A ACHS-7124 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. Pololu 4033
ACS724LLCTR-05AU current sensor module with a current measurement range from 0 to 5 A. It communicates via an analog interface. Pololu 4048
Module with an analog current sensor. Enables measurement of alternating and direct current up to 20 A. DFRobot SEN0214
ACS714 Current Sensor Carrier -5 to +5A
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 5A. DFRobot SEN0287
Current-to-voltage converter module designed for devices with a current signal output. It allows linear conversion of current signals from 0 to 25 mA into voltage signals from 0 to 3 V. DFRrobot SEN0262
INA169 current sensor module. The system can be supplied with the voltage from 2.7 V to 60 V and has an analog output. SparkFun SEN-12040
The current measurement with a value of 0 - 5A is realized by the ACS712-05 system based on the Hall effect. The system sensitivity is 185mV / A (analog signal).
The module with the ACS70331 current sensor with a direct current measuring range up to 2,5 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020652
ACS724LLCTR-20AU current sensor module with a current measurement range from 0 to 20 A. It communicates via an analog interface. Pololu 4044