ACHS-7121 Current Sensor Carrier - ACHS-7121 ± 10A current sensor module
ID: 586601
zł31.73
Tax included
zł25.80 tax excl.
Module with ACHS-7121 current sensor with a measuring range of direct and alternating current from -10 to 10 A. It communicates via an analog interface. Pololu 4030
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Module with a bidirectional Hall current sensor based on the ACHS-7121 system. It allows you to measure the current in the range from -10 to 10 A. The board is powered with the voltage from 4.5 V to 5.5 V and is intended for use in circuits with a logical voltage of 5 V. It offers a current path with low resistance (~ 0,7 mΩ) and electrical insulation up to 3 kV RMS. The output is a proportional analog voltage (185 mV/A) centered at 2.5 V with an error of ± 1.5%.
The sensor requires five connections to work properly: input current (IP+ and IP-), logic power (VCC and GND) and sensor output (OUT). Pin FILTER allows you to adjust the bandwidth of the plate by adding a capacitor to ground in parallel with the 1 nF capacitor that is already on the board. Without an additional external filter capacitor, the frequency response is approximately 80 kHz.
Features
- Hall effect differential detection
- The internal resistance of the conductive path is 0.7 mΩ
- Electrical insulation up to 3 kV RMS
- High bandwidth up to 80kHz for fast response times
- Integrated digital temperature compensation circuit
- The rugged sensor IC can tolerate 100 ms to 100 A transient currents
- Operating voltage 4.5 to 5.5 V
- Current measuring range from -10 to 10 A
- Output resolution 0.185 V/A
- Operating temperature range from -40°C to 110°C
- Dimensions: 17.8 x 20.3 mm
- Weight: 1.1 g
Kit contains
- ACHS-7121 Current Sensor Carrier module
- Straight 3-pin male connector
586601
Data sheet
- Interface
- Sygnał analogowy
- Zakres pomiarowy
- ±10 A
- Sposób podłączenia
- Szeregowy
You might also like
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
zł98.45
24h
Available quantity: 2
Available
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 5A. DFRobot SEN0287
zł90.15
24h
Available quantity: 1
Available
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.90
24h
Available quantity: 1216
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.08
24h
Available quantity: 120
Available
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.72
24h
Available quantity: 113
Available
Module with ACS724LLCTR-10AU current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4042
zł81.72
24h
Available quantity: 3
Available
Other products in the same category (16)
The current measurement with the value 0-20A is carried out by the ACS712-05 system based on the Hall effect. The sensitivity of the system is 100mV / A (analogue signal) .modACS712-20
zł14.66
24h
Available quantity: 25
Available
Bidirectional current sensor module based on the ACS724 circuit. It allows you to measure current in the range -50A to + 50A. It operates with a voltage of 4.5V to 5.5V and is intended for use in 5V systems. Pololu 4049
zł58.22
24h
Available quantity: 1
Available
Module with an analog current sensor. Enables measurement of alternating and direct current up to 20 A. DFRobot SEN0214
zł45.46
24h
Available quantity: 1
Available
Available
Module with ACS724LLCTR-10AU current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4042
zł81.72
24h
Available quantity: 3
Available
Voltage and current sensor module. It works with a shunt resistor and voltage divider and the INA-169 chip and can measure voltages up to 52 V and currents up to 90 A. SparkFun SEN-16408
zł136.90
6 weeks
No product available!
Module with ACS724LLCTR-05AB current sensor with a measuring range of direct and alternating current from -5 to 5 A. It communicates via an analog interface. Pololu 4041
zł47.71
24h
Available quantity: 5
Available
Analogue current sensor module. Allows measurement of AC and DC currents up to 50 A. DFRobot SEN0098-V2
zł73.89
24h
Available quantity: 3
Available
The current measurement with a value of 0 - 5A is realized by the ACS712-05 system based on the Hall effect. The system sensitivity is 185mV / A (analog signal).
zł8.94
24h
Available quantity: 47
Available
This board is a simple carrier of Broadcom’s bidirectional ±40A ACHS-7124 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. Pololu 4033
zł34.26
24h
Available quantity: 6
Available
Power monitor module that detects voltages up to 60 VDC and current up to 30 A. It uses the Allegro MicroSystems ACS37800 IC, which simplifies adding monitoring to power systems. SparkFun SPX-17873
zł179.00
6 weeks
No product available!
Module with ACS724 current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4045
zł58.01
24h
Available quantity: 1
Available
Current-to-voltage converter module designed for devices with a current signal output. It allows linear conversion of current signals from 0 to 25 mA into voltage signals from 0 to 3 V. DFRrobot SEN0262
zł24.54
24h
Available quantity: 9
Available
Module with an analog current sensor. It enables the measurement of AC and DC current up to 50 A. DFRobot SEN0098
zł134.91
4 weeks
No product available!
Module with ACHS-7123 current sensor with a measuring range of direct and alternating current from -30 to 30 A. It communicates via an analog interface. Pololu 4032
zł34.06
24h
Available quantity: 4
Available
The module with the ACS70331 current sensor with a direct current measuring range up to 2,5 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020652
zł48.34
24h
Available quantity: 3
Available
Module with ACHS-7121 current sensor with a measuring range of direct and alternating current from -10 to 10 A. It communicates via an analog interface. Pololu 4030