zł117.05 tax excl.
Dual MAX14870 Motor Driver is a dual DC driver compatible with Raspberry Pi that allows you to control two DC motors with 4.5-36V continuous current of 1.7A. Pololu 3759
Dual MAX14870 Motor Driver is a compact dual driver DC motors compatible with Raspberry Pi and plugged directly into the GPIO pins of the minicomputer. It allows you to control two DC motors with a voltage in the range of 4.5-36 V. The controller is based on two H MAX14870 bridges, thanks to which 1.7 A (2.5 A in peak) current can be drawn from each channel. The board has protection against reverse power connection. It is possible to power the Arduino board from a common power source with motors through an additional converter (not included).
The module was designed for new Raspberry Pi minicomputers in versions with a 40-pin connector: Model B + , Model A + , Raspberry Pi 2 Model B and Raspberry Pi 3 Model B.
Attention!
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Raspberry Pi 3 model B (Quad Core Broadcom BCM2837, 4x1.2GHz ARM Cortex-A53, RAM 1GB, 4xUSB, Ethernet, HDMI, Wifi, Bluetooth)
No product available!
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 36V and efficiently reduces it to 5V. The board measures only 0.7″ × 0.7″ yet delivers a typical continuous output current of up to 2.5A and features reverse voltage protection. Pololu 2858
The Raspberry Pi 3 Model B+ is boasting a 64-bit quad core processor BCM2837B0 running at 1.4GHz, dual-band 2.4GHz and 5GHz wireless LAN, Bluetooth 4.2/BLE, faster Ethernet, and PoE capability via a separate PoE HAT
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for assembly. Pololu 5052
No product available!
Pololu Dual G2 High-Power Motor Driver 24v18 is an extension that allows you to control two DC motors designed for Raspberry Pi. The motors can be supplied with 6.5-36V voltage and can draw a maximum current of 18A. Pololu 3756
No product available!
HAT with two-channel DC motor driver for Raspberry Pi. It has an operating voltage from 6 to 24 V and a continuous current of up to 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron HAT-MDD10
Extension module with a driver for two stepper motors based on the HR8825 system. Dedicated for Raspberry Pi minicomputers. Waveshare Stepper Motor HAT (B)
Dual DC motor controller designed for Raspberry Pi, which enables the engine to be supplied with voltage in the 4.5-28V range and power consumption in continuous operation of 2.6A (5A in peak) of two DC motors. Pololu 2762
DC motor controller that allows the movement of three drives to be controlled via an I2C interface. Kit with connectors for self-assembly. Pololu 5072
PCA9685 servo controller module dedicated to Raspberry Pi minicomputers. Allows control of 16 PWM channels. Waveshare Servo Driver HAT (B)
No product available!
DC motor driver that allows you to control the movement of three drives using the I2C interface. Board with soldered connectors. Pololu 5033
HAT module with TB6612FNG motor driver and PCA9685 PWM driver designed for Raspberry Pi minicomputers. The board is equipped with a 40-pin connector. Adafruit 4280
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5048
No product available!
DC motor controller that allows the movement of three drives to be controlled via an I2C interface. Pololu 5073
The Bus Servo Driver HAT (A) with the ESP32-WROOM-32 microcontroller enables simultaneous control of up to 253 ST and RSBL servos, supporting both wired and wireless communication in robotic applications. Designed for integration with Raspberry Pi, it features 5 V power supply from a converter and full support for UART and USB-C transmission. JSON command handling and automatic WiFi network startup allow for remote control and easy integration with various development environments. Ideal for robotic arm projects, walking robots, and other constructions requiring multiple servos with closed-loop control.
This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 Voperating range and are efficient enough to deliver a continuous 18 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation.
Module with a 2-channel driver for DC motors TB6612FNG designed to work with the Raspberry Pi. It can work with voltages from 6 to 12 V and currents up to 3 A. SB Components 21468
Adafruit 2348
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5056
No product available!
Dual MAX14870 Motor Driver is a dual DC driver compatible with Raspberry Pi that allows you to control two DC motors with 4.5-36V continuous current of 1.7A. Pololu 3759