A plate that allows you to easily connect wires to 0.5 mm FPC tape. This plate greatly facilitates the creation of prototypes and enables easy connection of FPC tapes to platforms such as Raspberry Pi that use popular 2,54 mm goldpins. A large solder field allows soldering not only 50-pin connector but also smaller ones.
Manufacturer
Responsible person
Pin header goldpin black 1x40 pins. Angled connector for through-hole assembly. 2.54mm pitch.
320x240 pixels display driven with the ILI9341 chipset, PiTFT, TFT shield v2 and 2.8" TFT breakout. Adafruit 1774
No product available!
The module is equipped with three 5A / 250VAC relays controlled by digital outputs. Relay contacts are led out to ARK screw terminals. Designed to work with NVIDIA Jetson Nano. Waveshare 3-CH Relay for Jetson Nano
No product available!
Camera module with Sony IMX219 sensor designed to work with NVIDIA Jetson Nano and RPi Compute Module. The camera is equipped with a matrix with a resolution of 8 MPx and has a viewing angle of 162°. Waveshare IMX219-160 IR-CUT Camera
A sound card in the form of a small device with a USB plug, designed to work with the Raspberry Pi and NVIDIA Jetson Nano minicomputer. Waveshare USB TO AUDIO
Portable game console based on Raspberry Pi CM3+ Lite, equipped with LCD IPS 2.8" display, battery and speaker. Waveshare GPM2803P0
No product available!
A-A type flexible hose (tape), 15 cm long. The tape has 16 wires and a 0.5 mm pitch
KAmodCSIextender modules are designed to work with Raspberry Pi cameras. KAmodCSIextender allows you to extend the signal from cameras using the HDMI <-> HDMI cable (up to 10 meters).
Bluetooth 5.0 module based on the BT401 chip. It allows you to send audio and support microSD cards up to 128 GB. DFRobot DFR0781
Evaluation Kit with Bluetooth 5.0 BT401. It is equipped with a microSD slot, microUSB connector and two audio outputs. DFRobot DFR0782
KAmodMC3635 is a module with the MC3635 three-axis accelerometer from mCube. The sensor allows the measurement of acceleration in the range of ±2g/±4g/±8g/±12g/±16g, the measurement frequency is from 14 to 1300 Hz. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMC3635
KAmodDIGIpot is a miniature digital potentiometer module. It allows, by means of two PU / PD inputs, to change the resistance value between the outputs A, W, B (compatible with the outputs of the analog potentiometer), using buttons or outputs of the microcontroller. Adjustment in 32 steps, value 10k.
Adapter for PS2 (female) connector. The connector is pre-soldered on the PCB. The pins have a 2.54 mm pitch, which facilitates their installation on the breadboard. Cytron Breakout Board PS2 Connector
Sound recording module that can store sounds up to 40 minutes long. It allows you to download the recordings to a computer via USB type C. DFRobot DFR0745
Ambient light sensor placed in a transparent hemisphere. It supports a detection range of 0 to 200 klx and communicates via the I2C interface. DFRobot SEN0390
VL806 is a compact USB 3.0 controller for integration into systems with a PCIe interface, providing fast data transfer, high device compatibility, and low power consumption. It is suitable for desktop computers, embedded systems, and expansion cards requiring stable and efficient communication with USB devices.
IPS LCD display 7" with a resolution of 1024x600 px with a touch panel. It uses the eDP interface and is compatible with LattePanda Alpha and Delta. DFRobot FIT0551
Knob with an inner diameter of 6 mm for mounting on a rotary potentiometer. Blue color
Plate allowing a connect the wires with goldpins to a maximum of 50- conductor , 0.5 mm FPC tape . Adafruit 1492