ESP32-S3 Reverse TFT Feather - WiFi and BLE module with ESP32-S3 chip and LCD display

Espressif ESP32-S3 WiFi module board with 32-bit dual-core Xtensa 32-bit LX7 processor. It offers 4 MB Flash memory and 512 kB SRAM and an RGB LED. It has a built-in ceramic WiFi/BLE antenna. Waveshare ESP32-S3-Zero-M

Module with WiFi and Bluetooth Espressif ESP32 WROOM. It integrates a set of peripheral devices - capacitive touch sensors, Hall sensors, SD card interface, Ethernet, fast SPI, UART, I2S and I2C. SparkFun WRL-17381

Development board based on a microcontroller with a RISC-V core. It offers support for WiFi 6, Bluetooth 5 and Zigbee 3.0 and Thread (IEEE 802.15.4) protocols. Uses the ESP32-C6-WROOM-1 module and two USB Type C connectors. ESP32-C6-DEVKITC-1-N8

Compact development kit from the M5StickC series equipped with ESP32 Pico and display. Includes accessories for building a watch. M5Stack K016-H

Module from the ESP32 series, combining a powerful microcontroller, Wi-Fi and Bluetooth 4.2 BLE. ESP-WROVER-B has a built-in PCB antenna, a large number of GPIO lines and small dimensions. Adafruit 3979

IoT development board equipped with ESP32 chip with WiFi and Bluetooth, has a USB-UART interface allowing programming via the USB port of the computer. DFRobot DFR0625

Compact M5Stack series development kit equipped with ESP32 Pico. It is based on a loudspeaker, I2S amplifier and a microphone. It will work in IoT-related projects, as a portable Bluetooth speaker or a voice-controlled device. M5Stack C008-C

Board with WiFi Espressif ESP32-S2 module and 0.96" LCD display. It offers 4 MB Flash memory and 8 MB SRAM. Leads are compatible with HAT modules for Raspberry Pi Pico. Waveshare ESP32-S2-LCD-0.96

Board with the WiFi Espressif ESP32-S2 module. Offers 4MB Flash and 8MB SRAM. Leads are compatible with HAT modules for Raspberry Pi Pico. Waveshare ESP32-S2-Pico-M

A development board that uses the ESP32-C3 chip based on the RISC-V architecture. It has built-in 400 KB of SRAM and 4 MB of Flash memory and a clock frequency of 160 MHz. Pro Micro offers a Qwiic connector that allows you to connect any sensor that communicates via the I2C bus. SparkFun DEV-23484

The ESP32-S3 A7670E 4G development board combines the ESP32-S3R2 microcontroller with the A7670E module, offering global LTE Cat-1, 2G, Wi-Fi, Bluetooth, and GNSS connectivity for advanced IoT applications. With support for lithium batteries and solar panels, as well as a built-in OV2640 camera, the board is ideal for remote monitoring projects, smart homes, and low-power applications.. Waveshare ESP32-S3-A7670E-4G-EN

Development board designed for IoT projects. It is equipped with a WiFi/Bluetooth module ESP32, LoRa 868 MHz, GPS and a basket for a Li-Ion 18650 battery. TTGO T-Beam V1.1

ESP-PROG is an advanced tool for programming and debugging Espressif microcontrollers such as ESP32, ESP32-C3, ESP32-S2, ESP32-S3 and ESP8266. With the built-in FT2232HL USB bridge, ESP-PROG converts the USB 2.0 interface to serial and parallel interfaces, offering functions of automatic firmware download, serial communication and online debugging via JTAG

The development board allows you to easily use the capabilities of ESP32 (Wi-Fi + Bluetooth BLE) from Espressif. There is a USB / UART converter on the board, and most of the GPIO line of the ESP-WROOM-32D module has been connected to pins with a pitch of 2.54mm. ESP32-DevKitC V4

Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, Li-Pol battery charging system. The board has soldered goldpin connectors. Adafruit 3591

M5Stack series development kit equipped with ESP32 Pico. Equipped with a 5x5 RGB LED matrix, it will work in IoT-related projects or in "wearable" devices. M5Stack C008-B