Ardi32 - development board with ESP32-S3-WROOM-1 module

Module with WiFi Espressif ESP32. It offers 8MB Flash, 2MB PSRAM, LiPo charging circuit and RGB LED. It is equipped with a STEMMA QT connector. Adafruit 5400

Set with Adafruit HUZZAH32 (ESP32) board and expansion module with 8 BME688 sensors (gas, pressure, temperature and humidity sensor). Bosch BME688 Gas Sensor Developer Kit

The ESP32-S3-BOX-3 is a development kit based on the ESP32-S3 SoC, ideal for creating AIoT, Edge AI, and IIoT applications. The ESP32-S3-WROOM-1 module supports WiFi 802.11 b/g/n (2.4 GHz) and Bluetooth 5.0, features 36 configurable GPIO pins, and includes a PCB antenna. It operates within a temperature range of -40 to +85°C with a supply voltage of 3.0 - 3.6V. The kit supports software solutions like ESP-BOX, ESP-SR, ESP-RainMaker, and ESP-Matter, facilitating the development of advanced IoT systems. ESP32-S3-BOX-3

The development board allows you to easily use the capabilities of ESP32 (Wi-Fi + Bluetooth BLE) from Espressif. There is a USB / UART converter on the board, and most of the GPIO line of the ESP-WROOM-32D module has been connected to pins with a pitch of 2.54mm. ESP32-DevKitC V4

Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5323

The low-power consumption micro-controller intentionally designed for Internet of Things (IoT) projects. The board integrates a Dual-Core ESP-WROOM-32 module, which supports MCU and Wi-Fi &Bluetooth dual-mode communication. DFR0478

Beetle ESP32 is a small (35 × 34mm) board thanks to which the creation of the Internet of Things (IoT) is very simple. The module was based on the ESP32 system, which allows for Bluetooth communication (compatible with Bluetooth 4.2) and WiFi. DFRrobot DFR0575

Board with the WiFi Espressif ESP32-S2 module. It offers 4 MB of Flash memory and 2 MB of SRAM and an RGB LED. It is equipped with a STEMMA QT connector. Adafruit 5325

Versatile ESP32 module with LoRa and Wi-Fi support, designed for monitoring people flow and creating mesh networks in difficult conditions, such as in areas cut off from the network. The device can detect Wi-Fi and Bluetooth signals, allowing estimation of the number of mobile devices in the environment without recording MAC addresses, which protects privacy. The module offers low power consumption, data storage on SD card and data transfer via LoRa WAN or MQTT, making it a reliable and self-sufficient solution for emergency communication. modTTGO LoRa32 v2.1

Board with the WiFi Espressif ESP32-C3 module. It offers 4 MB of Flash memory and 400 KB of SRAM and an RGB diode. It is equipped with a matrix of WS2812B programmable diodes

Espressif ESP32-C6 WiFi module board with RISC-V core. It offers 4 MB Flash memory and 512 kB SRAM and RGB diode. It has a built-in ceramic WiFi/BLE antenna. Version with soldered connectors. Waveshare ESP32-C6-Zero-M

Espressif ESP32-S3 WiFi module board with 32-bit dual-core Xtensa 32-bit LX7 processor. It offers 4 MB Flash memory and 512 kB SRAM and an RGB LED. It has a built-in ceramic WiFi/BLE antenna. Waveshare ESP32-S3-Zero-M

M5Stack series kit equipped with ESP32 and camera with OV2640 sensor. It has a built-in W5500 chip and can be powered by the RJ45 (PoE) connector. M5Stack U121

Evaluation kit with WiFi/Bluetooth module BLE ESP32-WROOM-32U. The board is equipped with a USB-UART converter, which through the microUSB connector allows you to power and program the board. Espressif ESP32-DevKitC-32U

Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, Li-Pol battery charging system. The board has soldered goldpin connectors. Adafruit 3591

A development board that uses the ESP32-C3 chip based on the RISC-V architecture. It has built-in 400 KB of SRAM and 4 MB of Flash memory and a clock frequency of 160 MHz. Pro Micro offers a Qwiic connector that allows you to connect any sensor that communicates via the I2C bus. SparkFun DEV-23484