

zł27.72 tax excl.
A 5-channel flame detector module for detecting a flame over a larger area. Detects fire with 5 sensors that are placed on the module every 30 degrees. It has a digital and analog output. modFLAME-5CH
ModFLAME-5CH is a 5-channel flame detector module used to detect a flame over a larger area. Detects fire with 5 sensors that are placed on the module every 30 degrees. This module sends an analog signal that is more precise and a digital signal that is easier to use. The sensitivity of the module is regulated by means of a built-in potentiometer.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
No product available!
Module with a flame sensor or other light sources with a wavelength in the range of 760 to 1100 nm. It was based on the YG1006 sensor (photovolver NPN). The sensor has a connector compatible with the Grove standard. Seeed studio 101020049
Module with a 10-channel AS7341 sensor that detects light in various wavelength ranges (color detection). It communicates via the I2C interface. Adafruit 4698
No product available!
Module with an analog TEMT6000 light intensity sensor. The output voltage increases with increasing intensity of the incident light. The sensor is powered by 5 V. SparkFun BOB-08688
No product available!
No product available!
Great way to upgrade a project that uses a photocell and needs RoHS compliance. Due to the high rejection ratio of infrared radiation, the spectral response of the ambient light sensor is close to that of human eyes. Adafruit 2748
Module with light sensor - LS06-S phototransistor. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020132
Module with a light sensor and a proximity sensor up to 5 cm. It allows you to read the illuminance from 0.01 to 64000 lux and communicates via the I2C interface. Pimoroni PIM413
TCS34725 RGB Color Sensor is a color sensor TCS34725 controlled by the I2C interface. It is powered by voltage in the range of 3.3 ... 5V and is intended for Arduino-compatible boards. DFRobot SEN0212
LTR390-UV UV light sensor module. Allows measurement of ultraviolet and visible light intensity. Equipped with a Gravity connector, it communicates via an I2C or UART interface. DFRobot SEN0540
Module with a flame sensor or other light sources with a wavelength in the range of 760 to 1100 nm. It was based on the YG1006 sensor (photovolver NPN). The sensor has a connector compatible with the Grove standard. Seeed studio 101020049
Ambient light sensor placed in a transparent hemisphere. It supports a detection range of 0 to 200 klx and communicates via the I2C interface. DFRobot SEN0390
Module with an analog TEMT6000 light intensity sensor. The voltage at the output is linearly correlated with the intensity of the incident light. The module is supplied with the voltage from 3.3 to 5V. DFRobot SEN0043
AS7331 UV light sensor module. It allows you to measure UV radiation on three channels: UVA (320-400nm), UVB (280-320nm) and UVC (200-280nm). Communication with AS7331 takes place via the I2C interface and the Qwiic connector. SparkFun SEN-23518
A module with a light sensor in the form of a photoresistor. There is a comparator and a potentiometer on the board. The module has a digital output
Module with a light intensity sensor LTR-329. It offers a measuring range from 1 to 65535 lux and a 16-bit resolution. Communication takes place using I2C. Adafruit 5591
Compact module with three I2C sensors, enabling measurement of temperature, humidity, pressure, light, proximity and motion. It offers two Qw/ST connectors, so you can quickly connect it to Raspberry Pi, Pico or other microcontrollers. Ideal for IoT applications, home automation and environmental analysis in mobile or stationary projects. Pimoroni PIM745
No product available!
Module with ultraviolet (UV) sensor based on the GUVA-S12D system. It allows measurement of radiation with a wavelength in the range from 240 to 370 nm. The module has a connector in accordance with the Grove standard. Seeed Studio 101020043
A 5-channel flame detector module for detecting a flame over a larger area. Detects fire with 5 sensors that are placed on the module every 30 degrees. It has a digital and analog output. modFLAME-5CH