DFRobot Gravity - Heart rate measurement module
ID: 562862
zł83.95
Tax included
zł68.25 tax excl.
Heart rate measurement module compatible with Arduino and Raspberry Pi (Gravity: Heart Rate Monitor Sensor For Arduino). It uses PPG technique, which in a simple and cheap way is able to measure the changing volume of blood. DFRobot SEN0203
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Heart rate measurement module compatible, among others with Arduino and Raspberry Pi . It uses PPG technique, which in a simple and cheap way is able to measure the changing volume of blood. The module has two holes on which the strap can be attached and thus place the sensor on the wrist, finger, or other place where the sensor is in contact with the skin. The sensor can transmit data in a digital or analog way depending on the setting of the slide switch.
Attention!
The product is not intended for professional medical diagnosis.
The product is designed to measure when the user is not moving. When the user is in motion, the results may be incorrect / incorrect.properties
- Output voltage: 0 ... Vin (for analog output), 0 / Vin (for digital output)
- Power consumption: <10 mA
- Gravity connector (PH2.0-3P)
- Supply voltage: 3.3 ... 6 V (5 V recommended)
- Dimensions 28 x 24 mm
An example of a sensor connection
Included
- Heart rate module (DFRobot SEN0203)
- Wrist strap
- Connecting cable Gravity (PH2.0-3P)
562862
You might also like
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł46.53
24h
Available quantity: 2
Available
Other products in the same category (16)
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip and communicates via the I2C or UART interface (Gravity connector). DFRobot SEN0518
zł116.35
4 weeks
No product available!
Available
Heart rate monitor module based on the popular MAX30101 and MAX32664. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-15219
zł207.16
24h
Available quantity: 6
Available
The module with a heart rate sensor and the SpO2 level dedicated to micro:bit. It is based on the MAX30102 chip and communicates via the I2C interface. SparkFun SEN-15271
zł62.77
24h
Available quantity: 2
Available
Disposable biomedical electrodes that allow you to perform experimental ECG measurements. DFRobot FIT0510
zł19.45
4 weeks
No product available!
The MyoWare Power Shield is designed to take two standard CR2032 coin cell batteries to power the MyoWare Muscle Sensor. We have made this board in a way that the coin cell batteries are connected in parallel for extended capacity at a nominal 3.0V. DEV-13684
zł24.33
24h
Available quantity: 2
Available
Module with heart rate and SpO2 sensor (oxygen saturation level) MAX30100 designed for M5Stack sets. M5Stack U029
zł54.00
24h
Available quantity: 3
Available
Evaluation board with built-in AD8232 heart monitor module and components placed in a way allowing effective implementation of medical and fitness applications, configuration of 2 or 3 electrodes
zł289.00
6 weeks
No product available!
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and a digital output in the form of pulses. Seeed Studio 101020033
zł72.41
6 weeks
No product available!
Module with heart rate sensor, SpO2 (oxygen saturation) and smoke levels. It is based on the MAX30101 chip and communicates via the I2C interface. Pimoroni PIM438
zł99.73
24h
Available quantity: 4
Available
The module with the MAX30100 chip that monitors the oxygen content in the blood and the heart rate. It consists of two LED diodes, a photodetector, optimized optics and low noise analog signal processing. modMAX30100
zł14.90
24h
Available quantity: 14
Available
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip, dedicated to the T-Wristband
zł38.90
24h
Available quantity: 2
Available
The sensor responds to chakra changes in the tissues by analyzing the reflected light (the module contains an illuminator and a sensor).
zł14.93
24h
Available quantity: 15
Available
A module with a sensor used to measure the activity of the heart. It allows you to strengthen and extract the heartbeat signals from biomedical electrodes. It has an analogue output and a heartbeat indicator (LED). SparkFun SEN-12650
zł94.70
24h
Available quantity: 4
Available
Designed to pair with the MyoWare Muscle Sensor; 10-segment bar graph shows the magnitude of the measured signal. The more muscle activation measured, the higher up the board the lit LEDs will go. DEV-13688
zł120.98
24h
Available quantity: 6
Available
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 103020024
zł154.13
24h
Available quantity: 2
Available
Heart rate measurement module compatible with Arduino and Raspberry Pi (Gravity: Heart Rate Monitor Sensor For Arduino). It uses PPG technique, which in a simple and cheap way is able to measure the changing volume of blood. DFRobot SEN0203