![PS01 - Pulse sensor PS01 - Pulse sensor](https://kamami.pl/19117-large_default/ps01-optoelectronic-pulse-sensor-module.jpg)
![PS01 - Pulse sensor PS01 - Pulse sensor](https://kamami.pl/19117-large_default/ps01-optoelectronic-pulse-sensor-module.jpg)
zł12.14 tax excl.
The sensor responds to chakra changes in the tissues by analyzing the reflected light (the module contains an illuminator and a sensor).
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
The optoelectronic pulse sensor module - allows you to detect the heartbeat by analyzing the change in parameters of illuminated tissues. The module uses an amplifier and noise eliminator, thanks to which the module is precise and reliable.
Evaluation board with built-in AD8232 heart monitor module and components placed in a way allowing effective implementation of medical and fitness applications, configuration of 2 or 3 electrodes
No product available!
Heart rate measurement module compatible with Arduino and Raspberry Pi (Gravity: Heart Rate Monitor Sensor For Arduino). It uses PPG technique, which in a simple and cheap way is able to measure the changing volume of blood. DFRobot SEN0203
Module with heart rate sensor, SpO2 (oxygen saturation) and smoke levels. It is based on the MAX30101 chip and communicates via the I2C interface. Pimoroni PIM438
Module with an EMG signal detector. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020058
Heart rate monitor module based on the MAX30102 chip. Powered with the voltage from 3.3 to 5V, communication via the I2C interface.
Heart rate monitor module based on the popular MAX30101 and MAX32664. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-15219
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip, dedicated to the T-Wristband
Gravity: Heart Rate Monitor Sensor is a sensor used to measure heart activity. Adapted for easy use with Arduino. SparkFun SEN0213
Disposable biomedical electrodes that allow you to perform experimental ECG measurements. DFRobot FIT0510
Module with heart rate and SpO2 sensor (oxygen saturation level) MAX30100 designed for M5Stack sets. M5Stack U029
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip and communicates via the I2C or UART interface (Gravity connector). DFRobot SEN0518
Sensor module for electromyography (EMG). Allows muscle activity to be studied and used to control devices. SparkFun DEV-21265
No product available!
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and a digital output in the form of pulses. Seeed Studio 101020033
No product available!
Heart rate measurement module compatible with Arduino and Raspberry Pi (Gravity: Heart Rate Monitor Sensor For Arduino). It uses PPG technique, which in a simple and cheap way is able to measure the changing volume of blood. DFRobot SEN0203
Designed to pair with the MyoWare Muscle Sensor; 10-segment bar graph shows the magnitude of the measured signal. The more muscle activation measured, the higher up the board the lit LEDs will go. DEV-13688
The MyoWare Power Shield is designed to take two standard CR2032 coin cell batteries to power the MyoWare Muscle Sensor. We have made this board in a way that the coin cell batteries are connected in parallel for extended capacity at a nominal 3.0V. DEV-13684
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240
No product available!
The sensor responds to chakra changes in the tissues by analyzing the reflected light (the module contains an illuminator and a sensor).