Single Lead Heart Rate Monitor - heart rate monitor with AD8232
ID: 546771
5906623417216
zł112.51
Tax included
zł91.47 tax excl.
A module with a sensor used to measure the activity of the heart. It allows you to strengthen and extract the heartbeat signals from biomedical electrodes. It has an analogue output and a heartbeat indicator (LED). SparkFun SEN-12650
Description
A module with a sensor that monitors the electrical activity of the heart. Myocardial activity data is sent as analog data. Due to the high noise of the heart activity data, the AD8232 chip was used in the module, which provides clear signals of PR and QT intervals. The module is adapted for use with Arduino kits and other elution plates. By using the "Serial Plotter" tool built into the Arduino IDE, the user can easily obtain an electrocardiographic (EKG) curve from analog data. Full documentation with examples of use is available on the product page.
Attention!
This product is not a medical device and is not intended to diagnose or treat it from a medical point of view.Features
- Operating Voltage: 3.3 V
- Analog Output
- Leads-Off Detection
- Shutdown Pin
- LED Indicator
- 3.5mm Jack for Biomedical Pad Connection
546771
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Available
Available
Other products in the same category (16)
The module with the MAX30100 chip that monitors the oxygen content in the blood and the heart rate. It consists of two LED diodes, a photodetector, optimized optics and low noise analog signal processing. modMAX30100
zł14.37
24h
Available quantity: 2
Available
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and a digital output in the form of pulses. Seeed Studio 101020033
zł72.41
4 weeks
No product available!
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240
zł232.78
24h
Available quantity: 2
Available
Module with pulse and SpO2 level sensor (oxygen saturation level). The module is based on the MAX30102 chip and communicates via the I2C interface.
zł9.83
4 weeks
No product available!
Heart rate monitor module based on the MAX30102 chip. Powered with the voltage from 3.3 to 5V, communication via the I2C interface.
zł9.83
4 weeks
No product available!
Heart rate monitor module based on the popular MAX30101 and MAX32664. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-15219
zł227.53
3 weeks
No product available!
Module with GSR skin resistance sensor. It is used to measure skin activity, which reflects the stress response and experienced emotions. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020052
zł46.84
4 weeks
No product available!
Module with an EMG signal detector. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020058
zł146.37
24h
Available quantity: 1
Available
Module with heart rate and SpO2 sensor (oxygen saturation level) MAX30100 designed for M5Stack sets. M5Stack U029
zł54.00
24h
Available quantity: 3
Available
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 103020024
zł139.17
24h
Available quantity: 1
Available
Module with a pulse sensor and SpO2 level (oxygen saturation level). It is based on the MAX30102 chip and MCU with heart rate and oximetry algorithm. Sensor communicates via the I2C interface. DFRobot SEN0344
zł69.90
24h
Available quantity: 1
Available
The module with a heart rate sensor and the SpO2 level dedicated to micro:bit. It is based on the MAX30102 chip and communicates via the I2C interface. SparkFun SEN-15271
zł73.84
24h
Available quantity: 1
Available
Module with heart rate sensor, SpO2 (oxygen saturation) and smoke levels. It is based on the MAX30101 chip and communicates via the I2C interface. Pimoroni PIM438
zł121.56
4 weeks
No product available!
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip, dedicated to the T-Wristband
zł38.08
4 weeks
No product available!
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip and communicates via the I2C or UART interface (Gravity connector). DFRobot SEN0518
zł111.32
24h
Available quantity: 1
Available
Iduino SE049 is a simple and functional heart rate sensor, ideal for educational and hobbyist projects in the fields of electronics and bioengineering. Thanks to its compatibility with Arduino and intuitive operation, it allows for the creation of custom measurement devices such as pulse meters or smart health-monitoring wristbands. It is suitable for mobile and stationary applications as part of a diagnostic or training system.
zł4.43
4 weeks
No product available!
A module with a sensor used to measure the activity of the heart. It allows you to strengthen and extract the heartbeat signals from biomedical electrodes. It has an analogue output and a heartbeat indicator (LED). SparkFun SEN-12650