New products
New products
zł59.04
Delivery date unknown
zł62.71
24h
Available
DFRobot Gravity IO Expansion Shield v7.1 to Arduino
ID: 561213
zł46.53
Tax included
zł37.83 tax excl.
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Arduino overlay, outputs Arduino plate lines as well as supply voltages and ground points to pin connectors. The board has contacts that allow you to place XBee series radio modules and screw connectors that allow you to connect an external power supply. The built-in switch allows you to freely program the board in the system without having to remove the XBee module.
Attention!
The set does not include Arduino board or XBee module, you should buy them separately.
properties
- Compatible with Arduino UNO , Due , Leonardo , Mega tiles
- Built-in RESET button
- Built-in screw connection for external power supply (voltage range: 7-12 V)
- Connector for Bluetooth and APC220 modules
- A switch that allows you to select programming / operating the XBee module
- Derived signals and voltages on male connectors (pins)
- Colored pin connectors
- Built-in LED "L" (attached to the D13 line of the Arduino board)
- Choice of operating voltage: 3.3 V or 5 V
561213
You might also like
Available
Other products in the same category (16)
The expansion module (shield) is designed for Arduino boards. It enables easy connection of 16x32 and 32x32 matrix displays. Requires self-assembly. Adafruit 2601
zł44.44
24h
Available quantity: 1
Available
RGB Panel Shield is an extension in the form of shield overlays designed for Arduino. With its help it is possible to control the RGB 32x32 LED display (refresh 1: 8). Communication with the display takes place via a 2x8 connector. SparkFun SPX-14721
zł40.47
24h
Available quantity: 1
Available
Powerful expansion shield for Arduino Mega. It is large enough to carry up to 3 Xbee slots, 1 microSD slot and shield headers for most Arduino shields on the market. DFR0165
zł50.66
24h
Available quantity: 2
Available
Extension board for Arduino Nano and Uno, 14 GPIO lines, connectors with I2C and UART interface lines. The board also has a RESET button and a voltage stabilizer
zł6.37
24h
Available quantity: 28
Available
Cap for Xbee and Arduino. It has been designed for wireless sensor networks such as WiFi, Bluetooth 2.0 / 4.0 and Zigbee. DFRobot DFR0015
zł43.48
24h
Available quantity: 1
Available
Gravity: Heart Rate Monitor Sensor is a sensor used to measure heart activity. Adapted for easy use with Arduino. SparkFun SEN0213
zł104.40
24h
Available quantity: 2
Available
(DFR0144) Relay Shield for Arduino V2.1
zł67.86
24h
Available quantity: 2
Available
e-Paper display controller module with a standard Arduino connector. It has a built-in MX25R6435F Flash memory with a capacity of 8 MB and a 24-pin FFC connector dedicated to e-Paper displays. Waveshare e-Paper Shield (B)
zł45.63
24h
Available quantity: 5
Available
The Beetle shield is designed to attach a Beetle controller for easy connecting servos and sensors. DFR0285
zł13.37
24h
Available quantity: 2
Available
The module with 4 relays is designed to work with Arduino. It allows you to control devices with operating parameters up to 250VAC/7A or 30VDC/10A. Seeed Studio 103030009
zł108.41
24h
Available quantity: 3
Available
Extension module (shield) with a signal generator for Arduino Pro Mini. It can trigger a sine, square or triangle waveform up to 3MHz. SparkFun BOB-11420
zł150.40
24h
Available quantity: 1
Available
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
zł24.40
24h
Available quantity: 16
Available
Expansion module with a joystick and buttons, resembling a gamepad. Enables the connection of the nRF24L01 radio module, Nokia 5110 display, Bluetooth module, I2C devices and Arduino kit. modKeyPad
zł13.75
6 weeks
No product available!
Arduino board for industrial applications dedicated to Arduino Portenta H7 boards. It allows the use of, among others artificial intelligence in production halls. Arduino AKX00032
zł1,809.00
3 weeks
No product available!
The Bluno Beetle Shield expands the Beetle\'s single analog and digital I/O pins to the 3 pin "gravity" interface, giving more power and ground connections and making it easier to attach gravity interface modules. It also includes a convenient external power supply and a 5-8v switch to power the board on and off. DFR0356
zł19.75
24h
Available quantity: 1
Available
Shield - Xbee w / o RF module
zł66.63
24h
Available quantity: 5
Available
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265