Gravity: Analog EMG Sensor
ID: 569863
5902186313293
zł225.72
Tax included
zł183.51 tax excl.
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240
Description
A module with an EMG sensor that detects the activity of human muscles and neurons. The sensor connects the filtering and boosting circuit. By using a differential input and an analog filter circuit, noise, especially power frequency interference, is reduced. The output module generates an analog signal ranging from 0 to 3 V, and the waveform of the output signal indicates muscle activity. The activity of muscles and neurons is picked up by an electrode which allows to obtain a good quality signal without the need to use a conductive gel. The product Wiki page offers a user manual as well as sample programs and generated graphs.
Features
Signal transmitter module
- Detection range: +/- 1.5 mV
- Electrode connector: PJ-342
- Module connector: PH2.0-3P
- Working voltage: 3V
- Output voltage: 0 to 3V
- Supply voltage: 3.3 V to 5.5 V
- Working temperature: 0 to 50 ℃
- Size: 22 x 35 mm
Electrode board
- Electrode connector: PJ-342
- Cable length: 50 cm
- Plate size: 22 x 35 mm
- Weight: 36 g
Kit contains
- EMG electrode board
- Wrist strap
- Electrode cable
- EMG signal transmitter module
- 3-pin Gravity analog cable
569863
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.42
Delivery date unknown
No product available!
Available
Board with ATmega1280 microcontroller from the AVR family, the user has 54 I/O lines, 14 PWM channels, 16 analog inputs. DFRobot DFR0003
zł89.20
Delivery date unknown
No product available!
Other products in the same category (16)
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and a digital output in the form of pulses. Seeed Studio 101020033
zł72.41
4 weeks
No product available!
Module with an EMG signal detector. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020058
zł149.04
24h
Available quantity: 2
Available
Heart rate measurement module compatible with Arduino and Raspberry Pi (Gravity: Heart Rate Monitor Sensor For Arduino). It uses PPG technique, which in a simple and cheap way is able to measure the changing volume of blood. DFRobot SEN0203
zł76.91
24h
Available quantity: 2
Available
Module with heart rate and SpO2 sensor (oxygen saturation level) MAX30100 designed for M5Stack sets. M5Stack U029
zł54.00
24h
Available quantity: 3
Available
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip, dedicated to the T-Wristband
zł38.08
4 weeks
No product available!
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 103020024
zł139.17
24h
Available quantity: 1
Available
The module with the MAX30100 chip that monitors the oxygen content in the blood and the heart rate. It consists of two LED diodes, a photodetector, optimized optics and low noise analog signal processing. modMAX30100
zł14.37
24h
Available quantity: 4
Available
Designed to pair with the MyoWare Muscle Sensor; 10-segment bar graph shows the magnitude of the measured signal. The more muscle activation measured, the higher up the board the lit LEDs will go. DEV-13688
Regular pricezł101.73zł23.90
24h
Available quantity: 11
Available
Module with heart rate sensor, SpO2 (oxygen saturation) and smoke levels. It is based on the MAX30101 chip and communicates via the I2C interface. Pimoroni PIM438
zł121.56
24h
Available quantity: 2
Available
The sensor responds to chakra changes in the tissues by analyzing the reflected light (the module contains an illuminator and a sensor).
zł15.03
4 weeks
No product available!
Iduino SE049 is a simple and functional heart rate sensor, ideal for educational and hobbyist projects in the fields of electronics and bioengineering. Thanks to its compatibility with Arduino and intuitive operation, it allows for the creation of custom measurement devices such as pulse meters or smart health-monitoring wristbands. It is suitable for mobile and stationary applications as part of a diagnostic or training system.
zł4.96
24h
Available quantity: 3
Available
Disposable biomedical electrodes that allow you to perform experimental ECG measurements. DFRobot FIT0510
zł19.84
24h
Available quantity: 2
Available
Available
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip and communicates via the I2C or UART interface (Gravity connector). DFRobot SEN0518
zł111.32
24h
Available quantity: 1
Available
Module with pulse and SpO2 level sensor (oxygen saturation level). The module is based on the MAX30102 chip and communicates via the I2C interface.
zł9.83
4 weeks
No product available!
Muscle Sensor Surface EMG Electrodes allow you to control your projects with your muscles. Adafruit 2773
zł26.36
4 weeks
No product available!
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240