![Pololu 2212 - 30:1 Micro Metal Gearmotor HP with Extended Motor Shaft Pololu 2212 - 30:1 Micro Metal Gearmotor HP with Extended Motor Shaft](https://kamami.pl/8072-large_default/pololu-2212---301-micro-metal-gearmotor-hp-with-extended-motor-shaft.jpg)
![Pololu 2212 - 30:1 Micro Metal Gearmotor HP with Extended Motor Shaft Pololu 2212 - 30:1 Micro Metal Gearmotor HP with Extended Motor Shaft](https://kamami.pl/8072-large_default/pololu-2212---301-micro-metal-gearmotor-hp-with-extended-motor-shaft.jpg)
zł80.74 tax excl.
30:1 Micro Metal Gearmotor HP with Extended Motor Shaft
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
30:1 Micro Metal Gearmotor HP with Extended Motor Shaft
This gearmotor is a miniature (0.94" x 0.39" x 0.47"), high-power brushed DC motor with 30:1 metal gearbox, similar to Sanyo’s popular 12 mm gearmotors. These units have a 0.365"-long, 3 mm-diameter D-shaped output shaft. This version also has a 4.5 x 1 mm extended motor shaft.
Key specs at 6 V: 1000 RPM and 120 mA free-run, 9 oz-in (0.6 kg-cm) and 1.6 A stall.
These tiny brushed DC gearmotors are intended for use at 6 V, though in general, these kinds of motors can run at voltages above and below this nominal voltage, so they should comfortably operate in the 3 – 9 V range (rotation can start at voltages as low as 0.5 V). Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor. The micro metal gearmotors are available in a wide range of gear ratios—from 5:1 up to 1000:1—and offer a choice between two different motors: high-power (HP) and standard. With the exception of the 1000:1 gear ratio versions, all of the micro metal gearmotors have the same physical dimensions, so one version can be easily swapped for another if your design requirements change. Please see the micro metal gearmotor comparison table for detailed specifications of all our micro metal gearmotors. This dynamically-sortable table can help you find the gearmotor that offers the best blend of speed, torque, and current-draw for your particular application. A more basic comparison table is available below.
Some versions of the gearmotors are sold with an additional 1mm-diameter output shaft that protrudes from the rear of the motor. This 4.5mm-long rear shaft rotates at the same speed as the input to the gearbox and offers a way to add a custom-built encoder to provide motor speed or position feedback.
Gear Ratio | Speed @ 6V | Stall Torque @ 6V | Stall Current @ 6V | ![]() Gearbox Shaft Only | ![]() Gearbox & Motor Shaft |
---|---|---|---|---|---|
5:1 | 6000 RPM | 2 oz-in | 1600 mA | 5:1 micro HP | |
2500 RPM | 1 oz-in | 360 mA | 5:1 micro | ||
10:1 | 3000 RPM | 4 oz-in | 1600 mA | 10:1 micro HP | 10:1 micro HP |
1300 RPM | 2 oz-in | 360 mA | 10:1 micro | ||
30:1 | 1000 RPM | 9 oz-in | 1600 mA | 30:1 micro HP | 30:1 micro HP |
440 RPM | 4 oz-in | 360 mA | 30:1 micro | 30:1 micro | |
50:1 | 625 RPM | 15 oz-in | 1600 mA | 50:1 micro HP | 50:1 micro HP |
250 RPM | 7 oz-in | 360 mA | 50:1 micro | 50:1 micro | |
75:1 | 400 RPM | 22 oz-in | 1600 mA | 75:1 micro HP | |
170 RPM | 9 oz-in | 360 mA | 75:1 micro | ||
100:1 | 320 RPM | 30 oz-in | 1600 mA | 100:1 micro HP | 100:1 micro HP |
120 RPM | 12 oz-in | 360 mA | 100:1 micro | 100:1 micro | |
150:1 | 200 RPM | 40 oz-in | 1600 mA | 150:1 micro HP | |
85 RPM | 17 oz-in | 360 mA | 150:1 micro | ||
210:1 | 140 RPM | 50 oz-in | 1600 mA | 210:1 micro HP | |
60 RPM | 27 oz-in | 360 mA | 210:1 micro | ||
250:1 | 120 RPM | 60 oz-in | 1600 mA | 250:1 micro HP | |
50 RPM | 32 oz-in | 360 mA | 250:1 micro | ||
298:1 | 100 RPM | 70 oz-in | 1600 mA | 298:1 micro HP | 298:1 micro HP |
45 RPM | 40 oz-in | 360 mA | 298:1 micro | 298:1 micro | |
1000:1 | 32 RPM | 125 oz-in | 1600 mA | 1000:1 micro HP | |
14 RPM | 70 oz-in | 360 mA | 1000:1 micro |
Note: The 1000:1 gearmotors can generate enough torque to damage themselves. The stall torque values given for those two motors are theoretical, and we strongly recommend you avoid stalling them.
![]() |
Micro metal gearmotor dimensions (units in mm). |
---|
The gearbox has a long (0.365" or 9.27 mm), 3 mm-diameter D-shaped metal output shaft, and the brass faceplate has two mounting holes threaded for M1.6 screws (1.6 mm diameter, 0.35 mm thread pitch). It weighs approximately 0.35 oz (10 g). Versions with the extended motor shaft have a 1mm diameter round shaft that protrudes 4.5 mm from the rear of the motor, between the two motor terminals; this is not pictured in the above dimension diagram.
Note: The gearbox on the 1000:1 and 1000:1 HP micro metal gearmotors is 12.5 mm long. All of the other micro metal gearmotors have 9mm-long gearboxes, as shown in the above dimension diagram.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
We offer a wide selection of metal gearmotors that offer different combinations of speed and torque. Our metal gearmotor comparison table can help you find the motor that best meets your project’s requirements.
![]() |
Some of the Pololu metal gearmotors. |
---|
![]() |
Pololu Micro Metal Gearmotor Bracket Pair - Black |
![]() |
Pololu Micro Metal Gearmotor Bracket Extended Pair |
![]() |
Pololu Ball Caster with 3/8" Metal Ball |
Data sheet
No product available!
A small, powerful motor with 5: 1 metal gear, 12 V operating voltage, 0.06 A to 0.75 A power consumption, 6800 RPM, maximum torque of 0.09 kg * cm and carbon brushes for extra durability. Pololu 3036
No product available!
Small motor with metal gear and encoder, rotation speed 300 RPM, operating voltage 6 V. GA46-N20E-0048
No product available!
A small medium-power motor with a 380: 1 metal gear, 6 V operating voltage, 0.04 A to 0.67 A power consumption, 57 RPM and a maximum torque of 3.6 kg * cm. Pololu 4792
No product available!
Small motor with metal gear and encoder, rotation speed 60 RPM, operating voltage 6 V. GA46-N20E-0044
No product available!
Pololu high power miniature motor with carbon brushes. 150:1 gear motor, shaft speed 220 rpm, torque 1,8kg*cm. The motor has an extended shaft, which makes it easy to attach the encoder. Pololu 3053
DC Micro motor module with metal gear with a gear ratio of 30:1. The motor is connected to the board containing the driver. DFRobot DFR0399
No product available!
10:1 Micro Metal Gearmotor
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 986.41:1 metal gearbox, making it a great choice for applications requiring fine control at very low speeds. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter.
No product available!
Miniature, 12V brush DC motor with metal gear and 15.25:1 gear ratio. It has a cross section of 10 × 12 mm, and the D-shaped output shaft with a length of 9 mm and a diameter of 3 mm. Pololu 4786
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 297.92:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
No product available!
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 51.45:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
Small, high power motor with 380: 1 metal gear, 6 V operating voltage, 0.1 A to 1.5 A power consumption, 85 RPM, maximum torque of 5 kg * cm, carbon brushes and double-sided shaft. Pololu 4797
No product available!
A small, low-power motor with a 210:1 metal gear, 6 V operating voltage, 0.02 A to 0.36 A current consumption, 65 RPM, a maximum torque of 1.6 kg*cm and a double-sided shaft. Pololu 2206
No product available!
30:1 Micro Metal Gearmotor HP with Extended Motor Shaft