

A module with an electret microphone and LMV324 amplifier that will allow you to detect voice, claps, door slams and other sounds. There are 3 outputs on the board: audio output, digital indication of the presence of sound and analog amplitude representation. The module can be supplied with the voltage in the range from 3.5 to 5.5 V. Full documentation is available on the product page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Pin header goldpin black 1x40 pins. Straight connector for through-hole assembly. 2.54mm pitch.
Cables for evaluation boards, set of 10 pcs., blue colour
Cables for evaluation boards, set of 10 pcs., red colour
Cables for evaluation boards, set of 10 pcs., green colour
A set of 40 female-female connection cables, in various colors, 17 cm long. CAB_F-F (Rainbow-40-17)
Module with MEMS type microphone (SPH0645LM4H-B). It allows you to receive a sound signal and send it using the I2S audio interface. Powered by 1.6 ... 3.6V voltage. Adafruit 3421
Module with PDM microphone. It allows you to receive a sound signal and send it using PDM modulation. Adafruit 3492
No product available!
A module with an electret microphone and MAX9812 amplifier, which will allow you to detect a voice, a clap or a door slam. Has an analog output
Gravity: Analog Sound Sensor is a sound sensor with Gravity analogue output. The module can be supplied with 3.3 ... 5V voltage. DFRobot DFR0034
KAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.
Module with an analog sound intensity sensor. It enables measurement in the range from 30 dB to 130 dB with a measurement error of ± 1.5 dB. The module returns the output voltage in the range of 0.6 to 2.6 V. DFRobot SEN0232
No product available!
Module with MEMS microphone; model SPW2430 with built-in amplifier. The plate also has a 3.3 V voltage stabilizer needed to power the microphone. Adafruit 2716
BOB-09868 - Breakout Board for ADMP401 MEMS Microphone, SparkFun
No product available!
MEMS SPU0414HR5H-SB analog microphone module. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020852
Module with WM8960 audio decoder that allows you to operate 1 W stereo speakers and two microphones via the I2S interface. Adafruit 4757
Audio module with two microphones and display designed to work with the Raspberry Pi. Pimoroni PIM524
A module with an electret microphone, amplifier and ADC converter dedicated to micro: bit. It communicates via the I2C interface. SparkFun SEN-15289
Expansion board compatible with STM32 Nucleo. Allows you to prototype solutions with digital microphones. STMicroelectronics X-NUCLEO-CCA02M2
Audio module with Jack (TRS) connector and THAT 1206 balanced line receiver. Offers low distortion and high attenuation. SparkFun BOB-14002
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V. BOB-12758
No product available!
The ICS43434 digital MEMS microphone module with an I2S interface that eliminates the need for A/D conversion and provides clean audio output in the range of 50 Hz to 15 kHz. With channel selection and low current consumption, it is suitable for stereo systems, voice recognition and portable applications. Compatible with popular microcontrollers, it provides high quality sound with low noise. Adafruit 6049
A module with an electret microphone and amplifier that will allow you to detect voice, clap, slam doors and other sounds using an analog or digital output. SparkFun SEN-12642