2-Channel Relay Module with Optoisolation-10A/250VAC Contacts, 5V Coil
ID: 1202349
5902186334014
zł9.90
Tax included
zł8.05 tax excl.
Two-channel relay module equipped with optoisolated control inputs and relays with 5V coils. Designed for controlling loads up to 10A at 250VAC from a microcontroller or development platforms
Description
The relay module is designed for controlling actuators using digital signals generated by microcontrollers and development platforms. The solution enables safe switching of loads powered by AC mains or DC voltage, such as lighting, motors, solenoid valves, and other electrical devices that require isolation from the logic control section.
The board is equipped with two electromagnetic relays with 5V coils, whose contacts allow switching currents up to 10A at 250VAC or 110VDC. Optoisolated control inputs separate the logic signals from the relay circuits, reducing interference and increasing the operational safety of the microcontroller.
Connection outputs
The module supports control signals with logic levels of 3.3V and 5V. The relays are activated by a low logic level. A jumper between the VCC and JD-VCC lines allows independent power supply of the logic section and the relay coils. Standard 2.54mm pitch pin headers and ARK screw terminals facilitate integration with installations and mounting in prototyping and educational projects.
Features
- Number of channels: 2
- Relay coil voltage: 5 V
- Logic supply voltage: 3.3 – 5 V
- Control method: active-low
- Maximum contact voltage: 250 VAC, 110 VDC
- Maximum contact current: 10 A
- Optoisolated control inputs
- Control connectors: 2.54 mm pin headers
- Load connectors: ARK screw terminals
- Operating temperature: -40°C ~ 85°C
1202349
Data sheet
- Output current
- 10A
- Number of channels
- 2
- Executive element
- Przekaźnik elektromagnetyczny
- Coil voltage
- 5 VDC
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A set consisting of the most commonly used goldpin connectors
zł5.01
24h
Available quantity: 98
Available
Other products in the same category (16)
Module with 5V relay and timer. It allows the implementation of delayed switching on or off of the circuit with adjustable time in the range from 1 s to 100 s and from 1 s to 15 min.
zł13.62
24h
Available quantity: 1
Available
Module with a 12 V relay and a timer. It allows you to turn the device on and off cyclically at a specified time using potentiometers. It can also operate in single trigger mode, which allows the device to be turned on after a signal has been applied for a specified period of time. The operating time can be adjusted from 1 s to 100 s or from 1 s to 15 min
zł14.55
4 weeks
No product available!
Module with 24V relay and timer. It allows the implementation of delayed switching on or off of the circuit with adjustable time in the range from 1 s to 100 s and from 1 s to 15 min.
zł13.60
24h
Available quantity: 4
Available
12V relay module with a radio receiver in a set with a remote control operating at 433 MHz.
zł34.08
4 weeks
No product available!
Module with MOSFET and a Gravity connector. It allows you to easily connect and control the voltage from 5V to 30V and the current up to 2.5A. DFRobot DFR0643
zł37.86
24h
Available quantity: 1
Available
Module with 4 relays JZC-11F with a load of 5A. It enables switching devices with high power using a microcontroller. I2C communication. SparkFun COM-16566
zł170.59
24h
Available quantity: 1
Available
Module with relay HF152FD 16A. It allows you to control devices with a current consumption of up to 16A using a low-power signal. The module has a relay activation time of about 10ms. DFRobot DFR0251
zł47.32
4 weeks
No product available!
Module with 2 relays controlled by the I2C interface. Each relay can switch currents up to 25 A at 12 to 280 V AC. SparkFun COM-16810
zł901.07
3 weeks
No product available!
Module with a relay and WiFi communication. Compatible with ESP-01 or ESP-01S
zł9.32
24h
Available quantity: 6
Available
Module with SSR M281 relay with a load of up to 1 A. The board is equipped with a Grove connector and is controlled by a digital input. Seeed Studio 101020603
zł29.75
24h
Available quantity: 3
Available
Module with 4 relays SRD-05VDC-SL-C with a load up to 10 A. The board was equipped with a Grove connector and communicates via I2C. Seeed Studio 103020133
zł67.35
24h
Available quantity: 3
Available
Module with 2 relays SRD-05VDC-SL-C with a load up to 10 A. The board is equipped with a Grove connector and is controlled by a digital signal. Seeed Studio 103020132
zł46.59
24h
Available quantity: 1
Available
Module with 8 relays SSR G3MC202P with a load up to 2 A. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 103020136
zł446.91
4 weeks
No product available!
Module with 2 relays SSR G3MC202P with a load up to 2 A. The board is equipped with a Grove connector and is controlled via digital inputs. Seeed Studio 103020134
zł188.52
24h
Available quantity: 2
Available
Module with relay SSR G3MC202P with a load up to 2 A. The board is equipped with a Grove connector and is controlled via digital input. Seeed Studio 103020137
zł87.59
4 weeks
No product available!
The module is equipped with three 5A / 250VAC relays controlled by digital outputs. Relay contacts are led out to ARK screw terminals. Designed to work with NVIDIA Jetson Nano. Waveshare 3-CH Relay for Jetson Nano
zł64.38
24h
Available quantity: 2
Available
Two-channel relay module equipped with optoisolated control inputs and relays with 5V coils. Designed for controlling loads up to 10A at 250VAC from a microcontroller or development platforms