![Main view Main view](https://kamami.pl/71352-large_default/waveshare-23452-power-management-hat-for-raspberry-pi-supports-charging-and-power-output-at-the-same-time-embedded.jpg)
![Main view Main view](https://kamami.pl/71352-large_default/waveshare-23452-power-management-hat-for-raspberry-pi-supports-charging-and-power-output-at-the-same-time-embedded.jpg)
zł95.93 tax excl.
A module dedicated to Raspberry Pi power management. It has a built-in RP2040 microcontroller that controls the operation of the device. Waveshare Power Management HAT (B) (EU)
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
A module dedicated to power management of Raspberry Pi minicomputers. It provides numerous functions related to power configuration, such as timed on/off switching and measurement of operating voltage and current consumption. The built-in MP28167-A buck-boost circuit guarantees fast response to transient load changes and the ability to quickly switch between different power sources. With the module, the minicomputer can be powered via a USB Type-C connector or via a JST PH2.0 connector with voltages from 3.3 to 4.2 V, including a lithium battery that can be charged using the built-in charger.
The module is controlled by an RP2040 microcontroller with two ARM Cortex-M0+ cores, 264 kB SRAM and 4 MB Flash memory. It communicates with the Raspberry Pi via a UART serial interface and GPIO pins and can be programmed by the user. All pins are brought out on 2.54mm connectors in a layout compatible with Raspberry Pi Pico boards. This allows the user to add new functionality in the form of HAT modules for the Raspberry Pi Pico, such as an LCD display to show operating parameters.
1. USB type C | 10. BOOT button |
2. MP28167-A | 11. PH2.0 battery connector |
3. CR1220 socket | 12. Fun connector |
4. RTC PCF85063 | 13. Status indicator |
5. W25Q32JVSSIQ NOR Flash 4 MB | 14. Power indicator |
6. RP2040 | 15. ETA6096 |
7. INA219 | 16. GPIO 40-pin |
8. PWR button | 17. RP2040 pinout |
9. RESET button |
Numerous circuits have been placed on the board, such as the PCF85063 RTC clock with a socket for a CR1220 battery to hold the voltage, or a user button that can be used to start the Raspberry Pi, safely shut down or any other custom function. The stability of the module's operation is ensured by reverse polarity or overload protection circuits. Full documentation and configuration examples are available on the product page.
Lithium Coin Cell Battery, 3V, 12x2mm
The latest version of the Raspberry Pi series: Raspberry Pi 4 model B with quad-core SoC (Broadcom BCM2711, Cortex-A72) working at 1.5GHz, 1GB RAM LPDDR4, Broadcom VideoCore VI layout.
The latest version of the Raspberry Pi series: Raspberry Pi 4 model B with quad-core SoC (Broadcom BCM2711, Cortex-A72) working at 1.5GHz, 2GB RAM LPDDR4, Broadcom VideoCore VI.
The long-awaited Raspberry Pi 4 model B with the SoC Broadcom BCM2711 SoC (4 x Cortex-A72) running at 1.5GHz, 4 GB LPDDR4 RAM and the Broadcom VideoCore VI graphics chip
The long-awaited Raspberry Pi 4 model B with the SoC Broadcom BCM2711 SoC (4 x Cortex-A72) running at 1.5GHz, 8 GB LPDDR4 RAM and the Broadcom VideoCore VI graphics chip
A module with 5 buttons and an RGB diode, designed to work with the Raspberry Pi. The buttons are connected to the minicomputer through the GPIO expander controlled by the I2C interface. Pimoroni PIM301
Expansion Shield X200 is a most cost-effective shield which could apply to Raspberry Pi Model B+ and Raspberry Pi 2 Model B. It integrates a lot of very useful functions such as RTC real time clock; audio input and output; VGA output; USB hub; WIFI; 8-way GPIO; DFR0357
Module with the Infineon Optiga SLB 9670 TPM 2.0 cryptographic chip. It uses the SPI interface for communication and is compatible with all versions of the Raspberry Pi. LetsTrust TPM
No product available!
A kit consisting of an M.2 HAT+ module and a Hailo-8L accelerator with a performance of 13 TOPS enables the rapid development of advanced real-time AI applications on the Raspberry Pi 5. This setup allows neural networks for object detection and segmentation to run on the Hailo-8L coprocessor, leaving the Raspberry Pi 5 CPU available for other tasks. The foundation has also prepared rpicam-apps libraries that significantly facilitate the creation of AI projects. Raspberry Pi SC1438
Modular USB and HDMI expander dedicated to the Raspberry Pi Zero and Zero 2W. It consists of three parts and has contact holes for easy integration with other POD modules. Waveshare Zero POD HDMI USB Hub Module
Set of cameras and a module that allows connecting two cameras to Raspberry using single MIPI connector. Arducam B0195S8MP
ZYMKEY 4i is a hardware security module designed for Rasbperry Pi. Supports encryption of system files on the memory card, allows for safe storage and generation of security keys.
Adapter enabling easy and quick connection of expansion modules compatible with the Modular DuoNect to selected Raspberry Pi platforms (with a 40-pin connector). Modally, MOD-79
Module with a capacitive fingerprint sensor for the Raspberry Pi. It communicates via the UART or USB interface. SB Components 21253
Overlay compatible with Raspberry Pi Zero, Zero W, Zero WH, 1A+, 3A+, 3B, 3B+, 4B. Includes LEDs, buttons, USB-UART converter (USB connector) and buzzer. Cytron Maker pHAT
Arduino shield designed to work with the Raspberry Pi minicomputer. It is possible to combine the capabilities of the minicomputer and the Arduino board in one device. DFRobot DFR0327
TFT LCD driver with DPI interface dedicated to Raspberry Pi. It allows you to operate resistive touch panels. Adafruit 2453
PCIe to M.2 adapter that allows you to connect M.2 NVMe SSD drives to Raspberry Pi 5 minicomputers. It works with M.2 SSD drives of sizes 2230/2242 and connects to the minicomputer via a 16-pin PCIe ribbon. Waveshare PCIe TO M.2 HAT+
Extension in the form of a HAT overlay with a DVB-T decoder designed for Raspberry Pi. Thanks to the module, it is possible to receive digital terrestrial television broadcast in the DVB-T and DVB-T2 standard. Raspberry Pi TV-uHAT
Module with barcode and QR scanner designed for Raspberry Pi. It allows you to read one-dimensional and two-dimensional codes using the intelligent image recognition algorithm. SB Components 22595
The module with 6 capacitive touch buttons and LED diodes, designed to work with the Raspberry Pi. The buttons are connected to the minicomputer via the CAP1166 controller, which communicates via the I2C interface. Pimoroni PIM272
A module dedicated to Raspberry Pi power management. It has a built-in RP2040 microcontroller that controls the operation of the device. Waveshare Power Management HAT (B) (EU)