

Module with 4-element segment display. Each of the four displays consists of 14 segments, so it can display not only numbers, such as the standard 7-segment display, but also letters and special characters. The display was connected to the VK16K33 controller operating with a voltage from 4.5 V to 5 V, so that when used with Arduino, a voltage level converter is not required. The user can configure the I2C address with two jumpers, which allows you to connect up to 4 such displays on one line. The module communicates via the I2C interface and is supplied with the voltage of 3.3 V. Full documentation with examples of use is available on the product page.
Data sheet
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Module with WiFi and Bluetooth Espressif ESP32 WROOM. It integrates a set of peripheral devices - capacitive touch sensors, Hall sensors, SD card interface, Ethernet, fast SPI, UART, I2S and I2C. SparkFun WRL-15663
Board with the ATmega328 microcontroller from the AVR family, there are 20 I/O lines, 6 PWM channels, 6 analog inputs at the user\'s disposal. SparkFun DEV-15123
Flexible Qwiic cable 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single male goldpin connectors. SparkFun PRT-17912
Flexible Qwiic cable, 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single female goldpin connectors. SparkFun PRT-17261
No product available!
Flexible 4-core cable, 200 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17258
Hub with Qwiic connectors that allows you to connect several boards to the evaluation kit. There is no built-in control system, but only splits one connector into 3 more. SparkFun BOB-18012
Module with GNSS MAX-M10S receiver. It can receive signals from GPS, GLONASS, BeiDou and Galileo constellations. It has an SMA connector for connecting an external antenna and a Qwiic socket. SparkFun GPS-18037
SparkFun Qwiic kit. Contains 10 wires of different lengths and tips. It allows you to connect Qwiic modules to a programming platform or to a prototype board. SparkFun KIT-15081
A cryptography kit that allows you to learn the basics of cryptographic authentication and the ATECC508A cryptographic co-processor. SparkFun KIT-18303
No product available!
End module of the communication system based on QwiicBus. It allows you to extend the range of the I2C bus. SparkFun COM-16988
No product available!
Kit with RFID reader (125 kHz) equipped with I2C interface. Works with ID-3LA, ID-12LA and ID-20LA series systems (ID-12LA set). The RFID reader is simply plugged into the module\'s connectors. SparkFun KIT-15209
Set of sensors with cables. They can detect gestures, movement, touch, sound, and measure humidity, temperature, altitude and acceleration. SparkFun DEV-16156
No product available!
Module with BME680 sensor for measuring environmental conditions such as concentration of volatile organic compounds (VOC), atmospheric pressure, temperature and humidity. I2C or SPI communication. SparkFun SEN-16466
No product available!
Module with an IO pin expander based on the TCA9534 system. It allows you to add 8 GPIO pins to an I2C-controlled project. SparkFun DEV-17047
Module with a satellite data receiver for transmission with L-band correction. It can be configured for use with various correction services to achieve centimeter-level positioning accuracy. SparkFun GPS-19390
No product available!
Air speed sensor module based on the FS3000-1005 chip. The board is equipped with Qwiic connectors. SparkFun SEN-18377
Module with PIR EKMB1107112 motion sensor, power consumption in standby mode up to 1 uA. The board communicates via I2C and is equipped with a Qwiic connector. SparkFun SEN-17375
Power module with a USB Type-C connector based on the STUSB4500 system. It enables powering devices with voltages ranging from 5 V to 20 V and currents up to 5 A. Configuration via the I2C interface. SparkFun DEV-15801
Module with a 4-element 14-segment display. The board is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun COM-16917