

Module with 4-element segment display. Each of the four displays consists of 14 segments, so it can display not only numbers, such as the standard 7-segment display, but also letters and special characters. The display was connected to the VK16K33 controller operating with a voltage from 4.5 V to 5 V, so that when used with Arduino, a voltage level converter is not required. The user can configure the I2C address with two jumpers, which allows you to connect up to 4 such displays on one line. The module communicates via the I2C interface and is supplied with the voltage of 3.3 V. Full documentation with examples of use is available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Module with WiFi and Bluetooth Espressif ESP32 WROOM. It integrates a set of peripheral devices - capacitive touch sensors, Hall sensors, SD card interface, Ethernet, fast SPI, UART, I2S and I2C. SparkFun WRL-15663
Board with the ATmega328 microcontroller from the AVR family, there are 20 I/O lines, 6 PWM channels, 6 analog inputs at the user\'s disposal. SparkFun DEV-15123
Flexible Qwiic cable 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single male goldpin connectors. SparkFun PRT-17912
No product available!
Flexible Qwiic cable, 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single female goldpin connectors. SparkFun PRT-17261
No product available!
Flexible 4-core cable, 200 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17258
No product available!
Module with a digital rotary encoder controlled by the I2C interface. The potentiometer has RGB LED backlight. The encoder generates post-movement information with 24 levels per revolution and rotation direction detection. SparkFun DEV-15083
A set for building a mechanical keyboard based on the Qwiic Pro Micro module. It allows you to create your own keyboard with 14 buttons with transparent caps. SparkFun SPX-17251
No product available!
Module with a button and re LED backlight. Controlled by the I2C interface, it has a built-in debouncing mechanism, pull-up resistors as well as interrupts and a FIFO queue. SparkFun BOB-15932
Module with digital barometer BMP581. It enables pressure measurement in the range from 300 to 1250 hPa with an accuracy of ± 5 Pa and communicates via I2C or SPI. SparkFun SEN-20170
No product available!
LiPo battery monitor module based on the MAX17048 chip. Allows the voltage and state of charge of the battery to be measured. SparkFun SPX-17715
Module dedicated to projects related to air quality monitoring. It uses the popular ENS160 and BME280 chips and provides a variety of environmental data such as Air Quality Index (AQI), TVOCs levels, CO2 equivalent (eCO2), atmospheric pressure, humidity and temperature. It communicates via the I2C interface and offers two Qwiic connectors. SparkFun SEN-22858
JST-SH 4-pin SMD connector for modules with Qwiic connectors. Pins\' pitch is 1 mm. Qwiic allows you to connect sensors via the I2C bus. SparkFun PRT-16766
No product available!
GPS module with 72-channel GNSS NEO-M8U receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. Built-in accelerometer and gyroscope. SparkFun GPS-16329
A set for building a mechanical keyboard based on the Qwiic Pro Micro module. It allows you to create your own keyboard with 14 buttons. SparkFun SPX-16184
A cryptography kit that allows you to learn the basics of cryptographic authentication and the ATECC508A cryptographic co-processor. SparkFun KIT-18303
No product available!
Module with 512 kbit (64kB) EEPROM. Communication is via the I2C interface. The module has 3 jumpers to select one of 8 addresses. SparkFun COM-18355
GPS module with NEO-M9N 92-channel GNSS receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. SparkFun GPS-17285
No product available!
Shield with Qwiic connectors designed for Raspberry Pi minicomputers. It allows you to easily connect the minicomputer with the Qwiic sensor system. SparkFun DEV-15945
No product available!
Advanced GNSS receiver based on the Quectel LG290P module, which supports four frequency bands: L1, L2, L5 and E6, enabling reception of signals from GPS, GLONASS, Galileo, BDS, QZSS and NavIC satellite systems. With support for SBAS and PPP, the module provides highly precise positioning, and the built-in anti-jamming unit minimizes electromagnetic interference, which ensures reliability in difficult conditions. The Qwiic connector allows easy integration with systems, and low power consumption makes it an ideal solution for applications requiring long-term battery operation. SparkFun GPS-26620
No product available!
Flexible Qwiic cable 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single male goldpin connectors. SparkFun PRT-17912
No product available!
Module with 16x2 characters LCD display and ATMega328p microcontroller. The user can communicate with the module through one of the serial interfaces: UART, I2C or SPI. SparkFun LCD-16396
Module with a 4-element 14-segment display. The board is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun COM-16917