- Out-of-Stock
ATJTAGICE3
ID: 184290
Atmel AVR JTAGICE3
Atmel AVR JTAGICE3
Mid-range in-circuit debugger and programmer for Atmel 8-bit and 32-bit AVR microcontrollers with on-chip debugging for source level symbolic debugging, NanoTrace (if supported by the device) and device programming.
JTAGICE3 is supported by AVR Studio 5.
The JTAGICE3 kit also includes adapters for use with the various physical interfaces.
>>> AVR JTAGICE3 on Atmel's website <<<
Mid-range in-circuit debugger and programmer for Atmel 8-bit and 32-bit AVR microcontrollers with on-chip debugging for source level symbolic debugging, NanoTrace (if supported by the device) and device programming.
JTAGICE3 supports the following programming modes:
- SPI
- JTAG
- PDI
- aWire
It also supports debugging using the following interfaces:
- debugWIRE
- JTAG
- PDI
- aWire
Features:
- Supports a large number of AVR devices
- Supports up to 3 hardware program breakpoints or 1 maskable data breakpoint (depending on the OCD module on the AVR device)
- Supports symbolic debug of complex data types including scope information.
- Supports up to 128 software breakpoints
- Level converters support 1.8V to 5.5V target operation
- Uploads 256Kb code in ~ 15 seconds (XMEGA using JTAG interface)
- Hi-Speed USB connection to host PC Firmware upgradeable for supporting future AVR devices
- Supports NanoTrace (depending on the OCD module on the AVR device; uses target device's memory)
- USB powered.
The JTAGICE3 kit also includes adapters for use with the various physical interfaces.
Package Contents
- JTAGICE3 unit
- USB High Speed cable ~1.5m
- 50-mil squid cable
- 50-mil IDC cable
- Adapter kit consisting of 10-pin 100 mil, 6-pin 100 mil, and 6-pin 50 mil
184290
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
JTAG interface galvanic separator that protects equipment against damage caused by potential differences, with a maximum clock frequency of 110 MHz, 3-5 V power supply, and isolation voltage up to 1 kVDC, equipped with multiple connectors and optical status signaling
zł399.00
24h
Available quantity: 41
Available
ATATMEL-ICE is a programmer designed to work with AVR microcontrollers with the On-Chip Debug function and microcontrollers with the Atmel ARM Cortex-M core. Available interfaces are JTAG, SWD, PDI, TPI, aWire, SPI and debugWire.
zł597.01
24h
Available quantity: 3
Available
Other products in the same category (16)
The evaluation kit is equipped with the Lattice iCE40 HX FPGA chip. The kit is supported by iCEcube2 and Verilog and Lucid languages. SparkFun DEV-16526
Retired
No product available!
Filament from ROSA3D made of high-quality ABS pellets. Placed on a cardboard thimble, on which 1 kg of 1.75 mm diameter filament is wound. ROSA3D ReFill ABS+ Black
Retired
No product available!
The switch module has a relay with a control function via a WiFi network. It can be connected to a WiFi network or act as a stand-alone access point. Shelly 1 Open Source
Retired
No product available!
No product available!
Audio recorder module that allows for multiple recording and playback of sounds
Retired
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
Kevin Skahill
Delivery date unknown
No product available!
2-channel M.2 SATA expander equipped with PCIe X1 connector. It supports support for SSDs that work with the SATA protocol. Waveshare PCIe-SATA-M2-2P-A
Retired
No product available!
No product available!
No product available!
No product available!
Starter kit with the Raspberry Pi 3 model A + minicomputer, the kit also includes the official case for RPI 3 model A and a card with pre-installed NOOBS software and a 116-page guide.
Retired
No product available!
Atmel AVR JTAGICE3