- Out-of-Stock
DIGITAL SOLDERING STATION RL1 - PRINTING BOARD AND CONTROLLED LAYOUT
Analogue soldering stations for temperature control use on / off binary systems. In this type of solutions, the temperature can oscillate around the set value even by several dozen degrees. If we want precise temperature stabilization, use the continuous control algorithm to control the heater. It is characterized by smoothly adjustable heater power - depending on the temperature.
The presented putty uses the PID (proportional-integral-derivative) algorithm. The clear LCD display presents all settings and allows you to control the operation of the device. The thermocouple type K was used as the temperature sensor. The soldering station is controlled by the ATmega8 microprocessor, to which the software was written using the GCC compiler.
The device is especially recommended in amateur electronics workshops and on the website
Selected parameters:
Download
Manufacturer
Responsible person
Multi-channel circuit testing multimeter that uses your smartphone or tablet, through Bluetooth 4.0, as a wireless, high-resolution graphical display. Each Mooshimeter is able to safely measure 600V at 10A with 24bit resolution from up to 150 feet away. TOL-13843
No product available!
Analog Test Shield for Arduino Development, AD/DA. Integrates DAC circuit and amplifier circuit.
No product available!
USB TO UART solution with USB micro connector. Waveshare 11315
No product available!
Waveshare WIFI501 is a mother board designed to be used with WiFi modules like WIFI232 series, WIFI-LPT100. It provides an easy way to test/evaluate these WiFi to UART modules
No product available!
No product available!
No product available!
Banana Pi M2+ is another ARM SoC powered development board that offers great computing performance in an ultra portable form factor. It is a 65mm square with Allwinner H3 Quad-core A7 SoC and 1GB DDR3 RAM
No product available!
Self-assembly DIY enclosure for Banana Pi M2+, transparent
No product available!
LSF0204PWR, 4-Bit Bidirectional Multi-Voltage Level Translator for Open-Drain & Push- Pull, TSSOP14
No product available!
Lithium Polymer rechargeable cell with a Protection circuit. Compatible with ODROID-C0
No product available!
MYIR MYC-JA5D44 is a single-board computer in the form of a card with SO-DIMM 200-pin connector. The SAMA5D44 processor from Atmel, based on Cortex-A5 cores, has been equipped. It can work with a maximum frequency of 600 MHz. It has 512 MB of DDR2 SDRAM, 512 MB of NAND Flash memory. GPIO ports, interfaces have been derived on the SO-DIMM 200-pin connector.
No product available!
MYIR MYC-C7Z020 is a single board computer module based on the MYC-C7Z020 chip. This system consists of a dual-core processor based on the Cortex-A9 core (667 MHz) and the Artix-7 FPGA chip. The board has 1 GB of DDR3 SDRAM, 4 GB of eMMC memory and 32 MB of QSPI Flash memory. The board is equipped with numerous peripherals, the outputs of which have been led out on two 140-pin connectors.
No product available!
This is the Green Adafruit 0.56" 4-Digit 7-Segment Display w/ FeatherWing Combo Pack! We also have these combo packs in Blue, Red, White, and Yellow! Adafruit 3107
No product available!
No product available!
The Arduino UNO WiFi board is based on the ATmega328 and it has an integrated ESP8266 WiFi Module. If you are starting out with Arduino, or starting with IoT, this is the board to get. A000133
No product available!
Printed circuit board with programmed layout for a dual-function acoustic switch. AVT3144 A +
No product available!
DIGITAL SOLDERING STATION RL1 - PRINTING BOARD AND CONTROLLED LAYOUT