- Out-of-Stock
These premium wires are stranded 26AWG wires with female terminals on one end and male terminals on the other end. Together with our 0.1" crimp connector housings, these wires can be used to make custom cables with 0.1" (2.54mm) connectors. The assortment of 12" (30 cm) wires includes five each of ten different colors.
![]() |
| 0.1" connector custom cable. |
|---|
These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connector housings on the ends. By combining these wires with our crimp connector housings, you can quickly and easily create custom cables with 0.1" (2.54mm) connectors that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards. Just pick the housing for the correct number of pins, pick the colors and genders for your wires, and snap them into the housings (note: it’s not easy to get the wires back out, so plan carefully!). No soldering is required!
You can easily make cable harnesses or assemblies that branch from one connector on one side to multiple connectors on the other (an example of this is shown in the picture to the right); you can also cut off one pre-crimped end and solder the wires directly to components to make swapping connections easy, as shown in the motor picture below.
The wires are available in six lengths—3" (7.5 cm), 6" (15 cm), 12" (30 cm), 24" (60 cm), 36" (90 cm), and 60" (150 cm)—and in ten colors:
![]() |
| 0.1" connector custom motor cable. |
|---|
These are the same colors as those used on resistor color codes and rainbow ribbon cable. The wire packs of different lengths include different quantities of wires. The table below shows the quantity included for a particular length-color combination:
| length | monochromatic pack quantity | rainbow pack quantity |
|---|---|---|
| 3" | – | 50 (5 of each color) |
| 6" | 10 | 50 (5 of each color) |
| 12" | 10 | 50 (5 of each color) |
| 24" | 5 | 50 (5 of each color) |
| 36" | 5 | 20 (2 of each color) |
| 60" | 2 | 10 (1 of each color) |
These wires can be purchased with male terminals on both ends, female terminals on both ends, or one male and one female terminals. These crimped terminals are designed for use with 0.1" (2.54 mm) male headers and female headers, solderless breadboards, and prototyping PCBs. Note that we also sell the crimp pins by themselves if you want to crimp your own wires.
![]() |
![]() |
| Female crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
| Male crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x1-Pin 25-Pack |
Manufacturer
Responsible person
Intel Edison platform with built-in antenna. Intel Atom 500MHz processor, 1GB RAM, supply voltage 3.15..4.5V, I2C, I2S, SD Card, SPI, UART, USB interfaces. EDI2.SPON.AL.S
No product available!
INTEL EDI2ARDUIN.AL.K Intel Edison Kit For Arduino, Atom, Wi-Fi/BT Compatible Module, Integrated Wi-Fi, 4GB Memory
No product available!
Orange Pi Plus 2 H3 Quad Core 1.6GHZ 2GB RAM 4K Open Source Development Board Mini PC
No product available!
Rainbow Case (Type B) for Raspberry Pi
No product available!
No product available!
Flora NeoPixel 30 RGB LED Strip in Reel - White Backing, 5 meters. Adafruit 1376
No product available!
With the Pmod Adapter for myRIO, you can now connect your myRIO to the expansive selection of Pmods offered by Digilent. 6002-410-013
No product available!
KAmodEPAPER is a module with a clear and energy-saving EPD (e-Paper) display of the GDE035A3 series. Thanks to the derived control signals and integrated in the inverter module, the display control is simple and no additional power lines are required
No product available!
Provides a 300 tie breadboard and 50 tie bus bar on an expansion card compatible with the NI myRIO Expansion Port (MXP). 210-283
No product available!
The GP2Y0A60SZ distance sensor from Sharp offers a wide detection range of 4″ to 60″ (10 cm to 150 cm) and a high update rate of 60 Hz. The distance is indicated by an analog voltage, so only a single analog input is required to interface with the module.
No product available!
The GP2Y0A60SZ offers a wide detection range of 4″ to 60″ (10cm to 150cm) and a high update rate of 60Hz. The distance is indicated by analog voltage - only a single analog input is required to interface with the module. Pololu 2476
No product available!
Shield for STM32 Nucleo with WiFi module b / g / n SPWF01SA. The module\'s firmware allows you to work as a client and UDP / TCP server, a web server, supports TCP / IP, TLS / SSL protocols. There are 16 GPIO lines available
No product available!
Shield X-NUCLEO-IHM09M1 from ST allows you to connect BLDC motor driver modules for STM32 Nucleo tiles
No product available!
STM32 Nucleo-144 development board with STM32F746ZGT6 MCU, supports Arduino, ST Zio and Morpho
No product available!
STM32 Nucleo-144 development board with STM32F429ZIT6 MCU, supports Arduino, ST Zio and Morpho
No product available!
The ST25TA02KB-P is a dynamic NFC/RFID tag IC with a digital General Purpose Output (GPO), embedding a 2 Kbit EEPROM that supports NDEF tag applications for NFC Forum Type 4
No product available!