- Out-of-Stock

This 1.72" x 0.79" x 0.79" gearmotor is a brushed DC motor with 154:1 metal gearbox that has the power to deliver both speed and torque. These units have a 0.276"-long, 4 mm-diameter D-shaped output shaft.
Key specs at 6 V: 90 RPM and 250 mA free-run, 120 oz-in (8.6 kg-cm) and 3.3 A stall.
The 20D mm line of brushed DC gearmotors are available in three different gear ratios, all of which have the same dimensions except for the length of the gearbox. The gearmotor face plate has two mounting holes threaded for M2.5 screws, and you can use our custom-designed 20D mm metal gearmotor bracket (shown in the left picture below) to mount the gearmotor to your project via these mounting holes and the screws that come with the bracket.
|
|
This gearmotor has an output shaft with a diameter of 4 m; the Pololu universal aluminum mounting hub for 4mm shafts can be used to mount our larger Pololu wheels (60mm-, 70mm-, 80mm-, and 90mm-diameter) or custom wheels and mechanisms to the gearmotor’s output shaft (see the right picture above). The gearbox’s output shaft also works directly with the 120mm-diameter Wild Thumper wheels, as shown below.
![]() |
Dagu Wild Thumper wheel 120×60mm (metallic red) with Pololu 20D mm metal gearmotor. |
---|
The picture below shows the dimensions (in mm) of the 20D mm line of gearmotors. The value of L
depends on the gear ratio of the gearbox: 29:1 is 15.7 mm, 73:1 is 17.2 mm, and 154:1 is 18.6 mm.
![]() |
20D mm metal gearmotor dimensions (units in mm, L=18.5mm). |
---|
Note: These motors are intended for use at 6 V. In general, these kinds of motors can run at voltages above and below this nominal voltage, so they should comfortably operate in the 3 – 9 V range. Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.
Note: The older, discontinued 25:1 and 67:1 versions of this gearmotor now had a different mounting hole spacing and work with a slightly different bracket. This bracket is not compatible with the 29:1, 73:1, and 154:1 20D mm gearmotors we currently offer.
We offer a wide selection of metal gearmotors that offer different combinations of speed and torque. Our metal gearmotor comparison table can help you find the motor that best meets your project’s requirements.
![]() |
Some of the Pololu metal gearmotors. |
---|
![]() |
Pololu Universal Aluminum Mounting Hub for 4mm Shaft Pair, 4-40 Holes |
![]() |
Pololu 20D mm Metal Gearmotor Bracket Pair |
![]() |
Pololu Bracket Pair for Discontinued 25:1 and 67:1 Metal Gearmotors 20D mm |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
No product available!
Cable with USB plugs type A and microUSB type B 2.0, cable length 3 m. LANBERG CA-USBM-10CC-0030-BK
No product available!
Single board computer with STM32F217VG microcontroller (ARM Cortex-M3, 1024 kB Flash, 128 kB RAM, LQFP100).
No product available!
2-pin ARK mounting strip, 5.0 mm pitch. 301-5.0-03P-12-00A(H)-BC
No product available!
No product available!
USB A 2.0 / USB C cable silicone, 1 m, black
No product available!
No product available!
COM-11556 - Thermochromatic Pigment - Sapphire Blue (20g)
No product available!
No product available!
GPS module with u-blox ZED-F9R. Uses Automotive Dead Reckoning (ADR) technology. Provides highly accurate and continuous positioning by combining the 3D IMU sensor, vehicle dynamics model, correction data and GNSS measurements. SparkFun GPS-16344
No product available!
No product available!
No product available!
No product available!
PCB for regulated symmetrical voltage supply. AVT1882 A
No product available!
Video splitter for connecting one input device to 8 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0008
No product available!
Transparent housing for Arduino UNO and Leonardo, open from the sides, upper plate with holes for shield connectors and ICSP connector
No product available!