- Out-of-Stock
Arduino ADK Rev3 - board with ATmega2560 and USB microcontroller
ID: 198056
Arduino ADK is a board in the ATmega2560 microcontroller and a USB interface that allows communication with Android smatrfones. The board provides, among others: 54 I / O lines, 14 PWM channels, 4 UART interfaces. A000069
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Arduino ADK R3 is a board with an ATmega2560 microcontroller and a USB host interface that allows communication with phones with the Android operating system.
The board is compatible with the Android Accessory Development Kit examples. The user has 54 digital I / O lines of which 14 can be used as PWM outputs, 16 analog inputs, 4 UART interfaces, 16 MHz quartz, USB connector, power connector, ICSP programming connector and RESET button.
Arduino ADK is built on the basis of Atmel's ATmega2560 microcontroller.
New features of the R3 version
- ATmega16U2 instead of 8U2 as a USB converter <-> Series
- Pin assignment in version 1.0: added SDA and SCL lines of the TWI interface next to the AREF pin and an additional two pins next to the RESET pin
properties
- ATmega2560 microcontroller
- Logic level 5 V
- Recommended 9 V power supply
- Permissible power supply voltage 7..18 V
- Digital I / O lines - 54 (14 with PWM output function)
- Digital inputs - 16
- Flash memory - 256 kB (8 kB occupied by the bootloader)
- SRAM - 8 kB
- EEPROM - 4 kB
- 16 MHz clock
To download
Code: A000069
198056
You might also like
No product available!
Other products in the same category (16)
No product available!
BeagleBone Blue features an Octavo Systems OSD3358 System-in-Package which incorporates a Texas Instruments AM335x Sitara™ Processor, TPS65217C Power Management IC, TL5209 LDO Voltage Regulator, a DDR3 SDRAM, and over 140 passive components. BBONE-BLUE
Retired
No product available!
No product available!
Banana Pi R2 is a mini-computer (router) equipped with a Quad-core ARM Cortex-A7 quad-core MediaTek MT7623N processor, 2 GB of RAM, WiFi module, Bluetooth 4.1 and connectors: HDMI, 5 x Ethernet, 2x USB 3.0. The set has a 40-pin GPIO connector, on which you can find UART, SPI, I2C and ID EEPROM interfaces.
Retired
No product available!
Tanenbaum Andrew S., van Steen Maarten
Delivery date unknown
No product available!
The AI accelerator with a USB connector is based on the Lightspeeur SPR2801S chip with a performance of up to 9.3 TOPS per watt. Optimized for use with single board computers based on Allwinner SoC chips, incl. Orange Pi. Orange Pi AI Stick Lite
Retired
No product available!
No product available!
No product available!
Diamond Brush thermal grease with the addition of diamond dust (10%). Great for use in computers (processors, graphics cards).
Retired
No product available!
Assembled solar collector differential controller. AVT5621 C
Retired
No product available!
No product available!
No product available!
No product available!
Permanent cylindrical neodymium magnet with a diameter of 8 mm and a height of 2 mm.
Retired
No product available!
No product available!
ACS711 Current Sensor Carrier -12.5 to +12.5A
Retired
No product available!
Arduino ADK is a board in the ATmega2560 microcontroller and a USB interface that allows communication with Android smatrfones. The board provides, among others: 54 I / O lines, 14 PWM channels, 4 UART interfaces. A000069