- Out-of-Stock
New products
New products New products
zł119.00
Delivery date unknown
zł119.00
Delivery date unknown
Power Cell - LiPo Charger/Booster
ID: 201134
PRT-11231 - Power Cell - LiPo Charger/Booster
PRT-11231 - Power Cell - LiPo Charger/Booster
Description:
The PowerCell board is a single cell LiPo boost converter (to 3.3V and 5V) and micro-USB charger in one. The board comes with a JST connector for a single cell LiPo battery, a micro-USB connector for the 5V charge input, and selectable 3.3V and 5V ouput pins (labeled out). There are also two charge pins broken out (labeled charge), so you can use another 5V power source to charge the batteries, if you dont have a micro-USB cable.
Weve also broken out the power-save and enable pins, so that you can have full control of the switching regulator. Keep in mind, if you keep your battery connected to the Powercell, it is recommended that you disable the switching regulator (pull EN low) in order to prevent the battery from discharging and reaching the under voltage cutoff on the battery itself. There is also an under-voltage lockout on the Powercell board which is tied to a solder jumper so that you can disable it if you like.
The micro-USB charger uses the MCP73831 and allows you to charge 3.7V LiPo cells at a rate of 100mA max. If you want to charge at a faster rate, you will need to connect a separate power supply to the pins labeled 5V and GND under the label charge.
The boost converter is based on the TPS61200 from TI and has solder jumper selectable 5V and 3.3V output, and an under voltage protection of 2.6V (which can be disabled via solder jumper on the back of the PCB).
Note: This board does not have reverse polarity protection, so please be sure to recognize the polarity of your connections!
- Dimensions: 1.03 x 0.95"
Features:
- MCP73831 Single Cell LiPo charger at 500mA
- TPS61200 Boost Converter
- Selectable output voltage 3.3 or 5V
- 5V @ 600mA max
- 3.3V @ 200mA max
- Undervoltage lock out at 2.6V (with disable jumper)
- Quiescent current, less than 55uA
- JST connector for LiPo battery
- micro-USB connector for charge power source
- Inductor: 4.7uH, 1.2A Sumida CDRH2D18
- Over temperature protection
Documents:
- Schematic
- Eagle Files
- Tutorial
- Datasheet (MCP73831T)
- Datasheet (TPS61200)
Replaces: PRT-10300
201134
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
No product available!
No product available!
Module with two 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM526
Retired
No product available!
7-color e-Paper display with a diagonal of 5.65" and a resolution of 600 x 448 pixels. It has a built-in controller that communicates via the SPI interface. Seeed Studio 104990859
Retired
No product available!
KAmodLSM303 is a module that allows you to measure the acceleration and the value of the magnetic field.
Retired
No product available!
No product available!
Graphic LCD 240x128, 144x104mm, LED backlight (WHITE), FSTN positive, T6963C controller, character generator
Retired
No product available!
MYIR MYC-C7Z010 is a single board module based on the MYC-C7Z010 chip. This system consists of a dual-core processor based on the Cortex-A9 core (667 MHz) and the Artix-7 FPGA chip. The board has 1 GB of DDR3 SDRAM, 4 GB of eMMC memory and 32 MB of QSPI Flash memory. The board is equipped with numerous peripherals, the outputs of which have been led out on two 140-pin connectors.
Retired
No product available!
No product available!
No product available!
3-CHANNEL DEVICE FOR REMOTE CONTROLLING - SET ASSEMBLED AND STARTED
Delivery date unknown
No product available!
"Tower to Mad Hornet, Roger that, clear to taxi to Runway 1 6 via taxiway Alpha. Winds are currently out of the south at 1 8 0 at 10 knots. Clear skies, visibility is 10+. It\'s a great day for flying!"
Every day is a great day for flying with your Ugears Mad Hornet vintage racer. Inspired by the Granville Brothers\' Gee Bee Model R-1 Super Sportster and other vintage racing aircraft of the 1930\'s, the Mad Hornet Airplane has a fat, teardrop-shaped fuselage and a cockpit located well aft, to give the pilot better visibility for tight turns around race course pylons. UGears 70183
Retired
No product available!
No product available!
Silicon spray oil from MICROCHIP, capacity 150ml. The oil can be used to remove squeaks and reduce the resistance of mechanisms
Retired
No product available!
No product available!
The Moto Compact folding scooter from Ugears is a clever, spring-driven addition to our family of two-wheeled DIY wooden models. For many youth, a motor scooter is their first form of motorized transport. It represents freedom, mobility, a fun way to get to school, activities, a first job. It\'s a ticket to explore the world beyond the neighborhood where you grew up. Capture that feeling of youthful freedom when you build this smart little folding scooter. UGears 70168
Retired
No product available!
PRT-11231 - Power Cell - LiPo Charger/Booster