- Out-of-Stock
RaZberry PI GPIO Daughter Card
ID: 200795
RaZberry PI GPIO Daughter Card, Z-Wave.me
RaZberry PI GPIO Daughter Card
Overview
The RaZberry module plugs in to your Raspberry PI board enabling it to connect to the Z-Wave network and function like a Z-Wave Home Automation Gateway.
The plug-in module includes firmware drivers and the Z-Wave stack (Z-Way). The browser-based development interface enables you to create your own software using an easy to understand and easy to use Java Script interface. Writing your own home automation app was never easier and never more affordable.
The RaZberry plug-in module includes:
- Z-Wave transceiver plugs into GPIO interface of the Raspberry PI
- Optimised firmware running on the Z-Wave transceiver chip
- Certified Z-Wave communication stack Z-Way - running on the Raspberry PI
- Z-Way AJAX-based User Interface for easy access to all Z-Wave functions of Z-Way and as a reference for your own User Interface enhancements.
- Note - Raspberry PI board is not included with this module
Technical Data
- Wireless: Z-Wave 868.4 MHz
- Dimensions: 40 x 20 mm
- Range: 25m in doors
200795
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Raspberry Pi 3 model B (Quad Core Broadcom BCM2837, 4x1.2GHz ARM Cortex-A53, RAM 1GB, 4xUSB, Ethernet, HDMI, Wifi, Bluetooth)
zł179.00
Delivery date unknown
No product available!
Other products in the same category (16)
The module enables connection of two devices with I2C interface working with different voltage levels. MOD-28.Z
Retired
No product available!
It is used to monitor the temperature measurement and other parameters. The expansion module has an I2C / 1-Wire converter (DS2482) through which DS18B20 temperature sensors can be connected using two or three wires. MOD-29.Z
Retired
No product available!
Power module with IRFR4105Z transistor (MOD-30.Z), maximum current 2A, 5V power supply or 5V - 12V range (selection by jumper)
Retired
No product available!
The module with the DS18B20 sensor is used to measure the temperature in the range from -55° C to + 125° C, with an accuracy of +/- 0.5° C in the range from -10° C to + 85° C. The module communicates via the 1-Wire interface, thanks to which it can be connected using 2 or 3 wires - depending on the configuration. Temperature measurement can be performed with an accuracy of 9 to 12 bits. MOD-31.Z
Retired
No product available!
Universal module with LM358 operational amplifier. Depending on the additional elements installed, the amplifier can be freely configured, eg as a reversing, non-inverting amplifier, voltage follower or an integrating amplifier. MOD-32.Z
Retired
No product available!
No product available!
The modally controlled modulation module MOD-34 / BZ allows wireless load control with a current consumption of up to 10A via a relay. Includes wireless module nRF24l01.
Retired
No product available!
No product available!
No product available!
No product available!
The module with the TXB0108 system enables the connection of systems operating with different voltage levels. It has 8-channels and is 2-way. The transmission direction of each channel is detected automatically. MOD-38.Z
Retired
No product available!
No product available!
The STM32 eXploreM0 module contains a 32-bit microcontroller with ARM Cortex M0 core, STM32F051C8T6 (64 kB Flash memory, 8 kB RAM, 48 MHz, HDMI-CEC, I2C, IrDA, LIN, SPI, UART / USART). The USB / UART converter allows programming of the microcontroller via a USB cable. MOD-40.Z
Retired
No product available!
The STM32 eXploreM0 + module contains a 32-bit microcontroller with ARM Cortex M0 + core, STM32L051C8T6 (64 kB of Flash memory, 8 kB RAM, 32 MHz, I2C, IrDA, SPI, UART / USART). The built-in USB / UART converter enables programming of the microcontroller via a USB cable. MOD-41.Z
Retired
No product available!
No product available!
The RGB LED ruler has 8 programmable LEDs WS2812B with a built-in control system. It is possible to set a specific color for each diode. The module has an IN input for controlling and an OUT output to which further light points or other modules from WS2812B can be connected. The supply voltage is from 3.5 to 5.3 V, and the input voltage +/- 0.5 V of the supply voltage
Retired
No product available!
RaZberry PI GPIO Daughter Card, Z-Wave.me