- Out-of-Stock
Nettemp Pi Hat - a Nettemp module for Raspberry Pi minicomputer
ID: 559377
Nettemp Pi Hat is a module that allows to connect eight trees of sensors with I2C/1-Wire interface and control of four relays outputs. Thanks to the extension board is possible to build in an easy way e.g. a multipunkt temperature controller.
Description
Nettemp project started for monitor of temperature in flats of author to make a optimalization of rooms heating.
Project assumptions included to provide a ready to use solution for wireless sensors management of temperature, humidity and light measurement and relays control. Software part of project based on simple installer and WWW interface.
Simple use of Nettemp'a:
- Temperature, pressure and humidity measurement in server room
- Heat control at home
- Air conditioning control
- Lighting control
On the website www.nettemp.pl you can find a description of the project, a demo video, a quick installation script or a list of compatible sensors.
Features
- Compatibility with NETTEMP software
- Extension board for Raspberry PI (version 3/2B/B+)
- Possibility of connection eight separate trees of sensors with I2C/1-Wire interface
- Module is supplied from a minicomputer
- Embedded UART-USB converter (based on chip CP2102 from Silicon Labs)
- Embedded four relays with NO/NC outputs
- Load is connected by screw terminals
- Maximum load of relay pins: 3A/250VAC
- Embedded real-time clock (M41T00S chip from STMicroelectronics)
- Embedded battery holder for RTC support
- Embedded buzzer
- Embedded connector allows to add a minicomputer without any wires
- Embedded pin connector GPIO 28-pin allows e.g. to add TFT display
- Mounting holes for Raspberry PI fastening
- Module size: 146mm x 80mm x 20mm
Nettemp Pi Hat allows to operate sensors, control the attached load and allows to use the touch interface.
Presentation of the NETTEMP program function (video)
Attention!
Raspberry Pi minicomputer and TFT display aren't included in the set!
Kit content
- Nettemp Pi Hat module
559377
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Computer cable - UTP cat6e twisted pair sold by the meter
zł2.73
24h
Available quantity: 224
Available
320×240, 3.2 inch Resistive Touch Screen TFT LCD, Designed for Raspberry Pi
zł94.27
24h
Available quantity: 2
Available
Raspberry Pi 3 model B (Quad Core Broadcom BCM2837, 4x1.2GHz ARM Cortex-A53, RAM 1GB, 4xUSB, Ethernet, HDMI, Wifi, Bluetooth)
zł179.00
Delivery date unknown
No product available!
Available
The Raspberry Pi 3 Model B+ is boasting a 64-bit quad core processor BCM2837B0 running at 1.4GHz, dual-band 2.4GHz and 5GHz wireless LAN, Bluetooth 4.2/BLE, faster Ethernet, and PoE capability via a separate PoE HAT
zł189.00
24h
Available quantity: 146
Available
The CR2032 3V 220mAh lithium battery is a compact, efficient and reliable power source, ideal for small devices such as watches or remote controls, ensuring long-lasting operation thanks to lithium technology
zł2.78
24h
Available quantity: 97
Available
Other products in the same category (16)
This in-system programmer can be used to program AVR microcontrollers and AVR-based controller boards, such as our Orangutan robot controllers and the 3pi robot. Pololu 3170
Retired
No product available!
EXtreme CC312U 3100mA power supply / car charger with two USB ports, allows you to charge phones, navigation, mp3 / mp4 players and connect Raspberry Pi computers
Retired
No product available!
AVT kit for self-assembly of an extremely effective bomb clock. AVT3128 B
Retired
No product available!
AVT kit for self-assembly of the battery capacity meter and the level of battery consumption. AVT5500 B
Retired
No product available!
433M wireless module for SPI interface, vertical pinheaders, 1.27mm pitch
Retired
No product available!
high performance e-compass, 3D accelerometer and 3D magnetometer module, I2C interface, LSM303DLHC on board
Retired
No product available!
three-axis digital output gyroscope, three-axis angular rate sensor module, I2C/SPI interface, L3G4200D on board
Retired
No product available!
High-power brushed DC motor with a 120:1 reduction gearbox, intended for operation at 4.5 V, 9.7mm-long gearbox, 3 mm-diameter D-shaped output shaft that is perpendicular to the motor shaft, and a built-in safety clutch. Pololu 1511
Retired
No product available!
High-power brushed DC motor, 120:1 reduction gearbox, intended for operation at 4.5 V, 9.7mm-long gearbox, 3 mm-diameter D-shaped output shaft that is offset from but parallel to the motor shaft, built-in safety clutch. Pololu 1512
Retired
No product available!
This compact, inexpensive plastic gearmotor (brushed DC motor with a 120:1 reduction gearbox) is well suited for use in small robots. While intended for operation at 4.5 V, it should run comfortably in the 3 V to 6 V range.
Retired
No product available!
Raspberry computer case: Pi 3 model B +, Pi 3 model B, Pi 2 model B and Pi 1 model B + in gray with metal
Retired
No product available!
Battery: Li-Ion; 3.7V; 1000mAh; Outputs: wires with 2-pin JST-PH connector; 50.8 mm x 33.5 x 5.9 mm. PRT-13813
Retired
No product available!
No product available!
This breakout board for TI’s DRV8880 microstepping bipolar stepper motor driver features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/16-step).
Retired
No product available!
Wheels fit 2 mm diameter output shafts such as the ones on our sub-micro plastic planetary gearmotors. Pololu - 2356
Retired
No product available!
JEKEN CE-6200A ultrasonic cleaner, with digitally adjustable working time, power 70 W and a capacity of 1.4 l. It is well suited for repair and maintenance of electronic components, PCBs, optical elements, as well as for the dissolution of polymers
Retired
No product available!
Nettemp Pi Hat is a module that allows to connect eight trees of sensors with I2C/1-Wire interface and control of four relays outputs. Thanks to the extension board is possible to build in an easy way e.g. a multipunkt temperature controller.