- Out-of-Stock
In the case of working with a MCU:
The UART GPS NEO-6M module supports software like u-center, GoogleEarth, etc., pretty easy to use. The following pictures show that using the module with u-center:
u-center user interface:

Positioning info on the text console:

This module provides 2 options for the onboard pinheader:
Development resources: demo codes, schematic, datasheets, etc.
Wiki: www.waveshare.com/wiki/UART_GPS_NEO-6M
| Part Number | UART GPS NEO-6M | UART GPS NEO-6M (B) | UART GPS NEO-6M-C | UART GPS NEO-7M-C | UART GPS NEO-7M-C (B) |
|---|---|---|---|---|---|
| GPS Module | U-BLOX NEO-6M | U-BLOX NEO-6M | NEO-6M | NEO-7M | NEO-7M |
| Pinheader | curved/horizontal | straight/vertical | curved/horizontal | curved/horizontal | straight/vertical |
| EEPROM | √ | √ | √ | X | X |
| GLONASS | X | X | X | √ | √ |
| Receive channel | 50 | 50 | 50 | 56 | 56 |
| Operating current | 45mA | 45mA | 45mA | 35mA | 35mA |
| Tracking sensitivity | -161dBm | -161dBm | -161dBm | -162dBm | -162dBm |
| Acquisition sensitivity (cold starts) | -147dBm | -147dBm | -147dBm | -148dBm | -148dBm |
| Navigation update rate | 5Hz | 5Hz | 5Hz | 5Hz | 5Hz |
| Oscillator | Crystal | Crystal | TCXO | TCXO | TCXO |
Manufacturer
Responsible person
L76K GNSS receiver module. It can receive data from GPS, GLONASS, BDS and QZSS systems. It uses a UART interface and offers an accuracy of up to 2 meters. Waveshare L76K GPS Module
3.5 "TFT display with touch panel, transparent housing and 16 GB SD card for Raspberry Pi 3. ArduCAM U470302
No product available!
Display with a touch screen (resistive panel) with a diagonal of 3.5 inches and a resolution of 480 x 320 pixels. Uses the SPI interface. Intended for use with the Raspberry Pi Zero / B + / 2/3 minicomputer. ArduCAM U470301
No product available!
A set of basic electronic components complete with contact plate, connecting cables and Mega2560 R3. It is ideal for beginner electronics who also know Arduino. ArduCAM KB0003
No product available!
A set of basic electronic components complete with contact plate, connecting cables and board compatible with Arduino UNO R3. It is ideal for beginner electronics who also know Arduino. Uctronics KB0002
No product available!
A set of basic electronic components complete with contact plate, connecting cables and Arduino UNO R3. It is ideal for beginner electronics who also know Arduino. ArduCAM KB0001
No product available!
Orange filament 1.75 mm 0.85 kg Easy PLA by Fiberlogy
No product available!
No product available!
No product available!
12 pin GPIO ribbon cable (200mm) for Odroid XU4 and Odroid XU4Q
No product available!
7 pin GPIO ribbon cable (20 cm) for Odroid C4
No product available!
No product available!
3-wire cable with JST-ZH plug, 30 cm, 3x1 JST, 1.5 mm pitch
No product available!
A set for building a four-wheel, remote-controlled vehicle. Equipped with a programmable Arduino Uno R3 controller and set of sensors. modARD_02
No product available!
No product available!
No product available!
800x480, 7 inch Multicolor Graphic LCD, with capacitive touch screen and stand-alone touch controller
No product available!