- Out-of-Stock
zł10,639.61
.png)
New products
New products New products
MyoWare Cable Shield
ID: 561544
The MyoWare Muscle Sensor is now designed to be wearable allowing you to attach biomedical sensor pads directly to the board itself. DEV-13687
Description
The MyoWare Muscle Sensor is now designed to be wearable allowing you to attach biomedical sensor pads directly to the board itself. However, there still may be cases where you want to mount the sensor pads away from the other hardware, this is where the MyoWare Cable Shield comes in. This shield provides a 3.5mm jack where you can attach a three electrode sensor cable allowing you to test and use the MyoWare Muscle Sensor without actually attaching it to your person.
The MyoWare Cable Shield is equipped with two rows of 3-pin plated through holes on each end of the board. This allows for standard 0.1" headers to be used to stack the shield with other MyoWare boards.
The MyoWare Muscle Sensor, that this shield attaches to, is an Arduino-powered, all-in-one electromyography (EMG) sensor from Advancer Technologies. The MyoWare board acts by measuring the filtered and rectified electrical activity of a muscle; outputting 0-Vs Volts depending the amount of activity in the selected muscle, where Vs signifies the voltage of the power source.
561544
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
You might also like
Available
The MyoWare Power Shield is designed to take two standard CR2032 coin cell batteries to power the MyoWare Muscle Sensor. We have made this board in a way that the coin cell batteries are connected in parallel for extended capacity at a nominal 3.0V. DEV-13684
zł37.71
Delivery date unknown
No product available!
Other products in the same category (16)
COM-11964 Button a white economy grade 100mm diameter (outside diameter) dome illuminated push button comes with an LED, securing nut and a long life horizontal microswitch.
Retired
No product available!
Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). The version is assembled. Adafruit 2029
Retired
No product available!
T-Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). Goldpin connectors are included, for self-assembly. Adafruit 1989
Retired
No product available!
FPC tape length 250 mm, 50 lines, pitch 0.5 mm. Adafruit 1682
Retired
No product available!
μHex is the first low-power controller which is compatible with Arduino. It is very suitable for the battery power supply environment. A 210mAh CR2032 cell battery could make it work 60 days long. DFR0343
Retired
No product available!
The Leonardo ETH is a microcontroller board based on the ATmega32U4 and the new W5500 TCP/IP Embedded Ethernet Controller (datasheet).
Delivery date unknown
No product available!
The DE0-Nano-SoC Development Kit presents a robust hardware design platform built around the Altera System-on-Chip (SoC) FPGA, which combines the latest dual-core Cortex-A9 embedded cores with industry-leading programmable logic for ultimate design flexibility
Retired
No product available!
Module for learning the basics of electronic engineering; illustrates the relationship between voltage, current, and allows the generation and observation of signals. It has the ability to sample the signal up to 200kSPS in a 16-bit converter. Powered from the USB port. ADALM1000
Retired
No product available!
Ribbon Cable, IDC Socket, IDC Socket, 40 Ways, 5.91 ", 150 mm, 2.54 mm
Retired
No product available!
No product available!
No product available!
FRAM memory with a capacity of 4kbit by Cypress Semiconductor, communicates via the I2C bus, the power supply voltage is in the range 2.7 - 3.6V. The system has an SOIC8 housing
Retired
No product available!
A small Li-Pol battery with a nominal voltage of 3.7 V and a capacity of 1350 mAh. Leaded wires, dimensions: 5 x 37 x 59 mm. Akyga LP503759
Retired
No product available!
Thermistor for THT assembly with a resistance of 10k, a temperature coefficient of 3380K and accuracy of 1%. The sensor body is Ø2.5x4mm
Delivery date unknown
No product available!
KAmduino UNO is a development board with functionality and dimensions typical for Arduino UNO. Thanks to the built-in ATmega328P microcontroller and the FT231X chipset, the board can be programmed via a USB interface using the Arduino environment. KAmduino UNO
Retired
No product available!
K64 microcontroller with ARM® Cortex®-M4 core, 1MB Flash memory, 256kB RAM, 120MHz, SPI, I2C, I2S, UART, CAN, USB OTG, ADC, DAC, RTC, DMA, LQFP100
Retired
No product available!
The MyoWare Muscle Sensor is now designed to be wearable allowing you to attach biomedical sensor pads directly to the board itself. DEV-13687