- Out-of-Stock
Gravity: GPIO Shield for Arduino
ID: 562581
Gravity: GPIO Shield for Arduino is an I / O port expander compatible with Arduino UNO. It allows to expand the capabilities of the base board by providing a total of 36 digital and analogue pins as well as UART and I2C interfaces. DFRobot DFR0334
Description
Gravity: GPIO Shield for Arduino is an I / O port expander compatible with Arduino UNO. It allows you to expand the capabilities of the base plate by providing a much larger number of pins than are available on Arduino boards. Shield provides a total of 36 pins, including 14 Arduino digital inputs / outputs, 6 Arduino analog pins and 16 additional I / O pins controlled via the I2C interface. 16 additional pins are available thanks to the PCA9555 chip. On the board, all digital and analog pins have been positioned in a special way together with VCC and GND pins in a manner analogous to the DFRobot "Gravity" standard. This makes it even easier to connect modules with DFRobot sensors to Arduino tiles. The board also has derived I2C and UART serial interfaces. The PCB's power supply can be realized by Arduino pins or from an external power supply (selection by means of a jumper).
properties
- Intended for Arduino tiles
- Arduino digital pins: 14, D0 - D13
- Arduino analog pins: 6, A0 ~ A5
- GPIO pins available via the I2C interface: 16, P0.0 ~ P0.7; P1.0 ~ P1.7
- I2C interface: 1
- UART interface: 1
- Reset button: 1
- Power supply: 5 VDC / External power supply (switched by jumper)
- Dimensions: 53.34 x 54.48 mm
- Weight: 30 g
562581
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.57
24h
Available quantity: 89
Available
(DFR0144) Relay Shield for Arduino V2.1
zł60.71
24h
Available quantity: 1
Available
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł21.92
24h
Available quantity: 4
Available
The overlay solves the problem of limitations in the use of multiple overlays compatible with Arduino UNO R3. The board allows you to connect different shields without their mutual influence on each other (eg without conflict on the UART bus or GPIO lines). Extension dedicated for Arduino Mega and ADK devices. DFRobot DFR0256
zł60.32
24h
Available quantity: 2
Available
Module with a 16-channel GPIO expander with the ability to control LEDs. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4886
zł27.06
24h
Available quantity: 2
Available
Other products in the same category (16)
Thermopad, thermo-adhesive tape, double-sided adhesive 20mm x 130mm x 1mm, 2.4W / mK, AG Thermopiles, RoHS
Retired
No product available!
Display with 7 "TFT LCD touch screen for Odroid C0, C1, C1 +, C2, Xu3 and XU4 computers The display has an HDMI interface for displaying images and USB for a touch screen resolution 1024x600 pixels
Retired
No product available!
Xprotolab Plain is an Oscilloscope, Logic Analyzer, Waveform & Clock generator all in one tiny, light weight and low cost package which are fully compatible with ODROID-C1/C2/XU4 Linux platforms
Retired
No product available!
AG chemical preparation, sodium persulfate for the etching of printed circuit boards. It dissolves very quickly and does not crystallize out of the solution. Purse 100g
Retired
No product available!
A liquid for cleaning printed circuit boards based on isopropyl alcohol, perfectly removes binder residues, as well as lubricants and oils. MICROCHIP
Retired
No product available!
Tape, in the form of a braid, to remove the excess of molten solder brazing material during soldering and desoldering of electronic components 1.5m
Retired
No product available!
Anti-static brush, brush for cleaning printed circuit boards, elements after the soldering process
Retired
No product available!
Antimagnetic tweezers, sharp, made of stainless steel, resistant to most solvents and cleaning agents. 00-sa
Retired
No product available!
ZD-409 resistance soldering machine with a power of 48W is a tool useful when disassembling SMD and DIL components on printed circuits.
Retired
No product available!
Multi-channel circuit testing multimeter that uses your smartphone or tablet, through Bluetooth 4.0, as a wireless, high-resolution graphical display. Each Mooshimeter is able to safely measure 600V at 10A with 24bit resolution from up to 150 feet away. TOL-13843
Retired
No product available!
Analog Test Shield for Arduino Development, AD/DA. Integrates DAC circuit and amplifier circuit.
Retired
No product available!
USB TO UART solution with USB micro connector. Waveshare 11315
Retired
No product available!
Waveshare WIFI501 is a mother board designed to be used with WiFi modules like WIFI232 series, WIFI-LPT100. It provides an easy way to test/evaluate these WiFi to UART modules
Retired
No product available!
No product available!
No product available!
Banana Pi M2+ is another ARM SoC powered development board that offers great computing performance in an ultra portable form factor. It is a 65mm square with Allwinner H3 Quad-core A7 SoC and 1GB DDR3 RAM
Retired
No product available!
Gravity: GPIO Shield for Arduino is an I / O port expander compatible with Arduino UNO. It allows to expand the capabilities of the base board by providing a total of 36 digital and analogue pins as well as UART and I2C interfaces. DFRobot DFR0334