- Out-of-Stock
SparkFun AutoDriver - Stepper Motor Driver (v13)
ID: 562732
BOB-13752
Description
The SparkFun AutoDriver board is based on the STMicro L6470 dSPIN stepper motor driver. This powerful chip allows you to control a stepper motor with a voltage from 8 to 45V at 3Arms over an SPI connection. The AutoDriver board has been designed to be easily integrated into a project, even with multiple boards. Just connect your motors and your SPI-capable microcontroller and get steppin'!
STMicro’s L6470 is a 3A, 8–45V bipolar stepper motor driver. It has built-in overcurrent detection, undervoltage detection, overtemperature detection, stall detection, a 5-bit ADC, and a switch input that can be used for either user jog control or as a hard stop function. As if that weren’t enough, it also features microstepping support (up to 128 microsteps per full step) and PWM drive voltage limiting. Please keep in mind that the L6470 requires a great deal more configuration and adds software complexity to your system.
Unlike most stepper motor drivers, the dSPIN is controlled over an SPI link. It has an onboard 16MHz oscillator, which allows it to autonomously execute movement commands. That means no more counting steps in your code! It also supports customized acceleration and deceleration profiles to prevent jerky starts and stops. Onboard registers track current speed and location.
This new version of the SparkFun AutoDriver’s hardware is slightly different from the previous revision. It has been modified to make it easier to daisy-chain multiple boards together with simple 10-conductor ribbon cables for data and 6-conductor ribbon cables for control. The library has been updated as well, with more information found in the Hookup Guide below.
The logic supply voltage supports both 3.3V and 5V I/O levels.
Features
- Supports up to 128 Microsteps per Full Step
- Daisy-Chain Capable
- Over-Temperature Detect
- Over-Current Detect
- Under-Voltage Detect
- PWM Drive-Voltage Limiting
- SPI Controlled
- Onboard Oscillator and Speed/Location Registers
- Stall Detection
- 5-bit ADC
562732
Data sheet
- Output current
- 3A
- Number of channels
- 2
- Supply voltage min
- 8 V
- Supply voltages max
- 45 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
DRV8825 Stepper Motor Driver Carrier is a DRV8825 stepper motor driver that allows you to supply a bipolar current of up to 1.5 A per phase, without using a heat sink. The system can be supplied with voltage up to 45V, in the set there is a heat sink. Polol 2133
zł60.10
24h
Available quantity: 1
Available
DRV8825 Stepper Motor Driver Carrier is a DRV8825 stepper motor driver that allows you to supply a bipolar current of up to 1.5 A per phase, without using a heat sink. The system can be supplied with voltage up to 45V, in the set there is a heat sink. It is compatible with Polol 2133
zł9.05
Delivery date unknown
No product available!
Simple to use stepper motor driver, compatible with anything that can output a digital 0..5V pulse or 0..3.3V pulse. Connect a 4-wire stepper motor and a microcontroller and you’ve got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors. ROB-12779
zł87.16
Delivery date unknown
No product available!
Other products in the same category (16)
AVT kit for self-assembly of the battery capacity meter and the level of battery consumption. AVT5500 B
Retired
No product available!
433M wireless module for SPI interface, vertical pinheaders, 1.27mm pitch
Retired
No product available!
high performance e-compass, 3D accelerometer and 3D magnetometer module, I2C interface, LSM303DLHC on board
Retired
No product available!
three-axis digital output gyroscope, three-axis angular rate sensor module, I2C/SPI interface, L3G4200D on board
Retired
No product available!
High-power brushed DC motor with a 120:1 reduction gearbox, intended for operation at 4.5 V, 9.7mm-long gearbox, 3 mm-diameter D-shaped output shaft that is perpendicular to the motor shaft, and a built-in safety clutch. Pololu 1511
Retired
No product available!
High-power brushed DC motor, 120:1 reduction gearbox, intended for operation at 4.5 V, 9.7mm-long gearbox, 3 mm-diameter D-shaped output shaft that is offset from but parallel to the motor shaft, built-in safety clutch. Pololu 1512
Retired
No product available!
This compact, inexpensive plastic gearmotor (brushed DC motor with a 120:1 reduction gearbox) is well suited for use in small robots. While intended for operation at 4.5 V, it should run comfortably in the 3 V to 6 V range.
Retired
No product available!
Raspberry computer case: Pi 3 model B +, Pi 3 model B, Pi 2 model B and Pi 1 model B + in gray with metal
Retired
No product available!
Battery: Li-Ion; 3.7V; 1000mAh; Outputs: wires with 2-pin JST-PH connector; 50.8 mm x 33.5 x 5.9 mm. PRT-13813
Retired
No product available!
No product available!
This breakout board for TI’s DRV8880 microstepping bipolar stepper motor driver features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/16-step).
Retired
No product available!
Wheels fit 2 mm diameter output shafts such as the ones on our sub-micro plastic planetary gearmotors. Pololu - 2356
Retired
No product available!
JEKEN CE-6200A ultrasonic cleaner, with digitally adjustable working time, power 70 W and a capacity of 1.4 l. It is well suited for repair and maintenance of electronic components, PCBs, optical elements, as well as for the dissolution of polymers
Retired
No product available!
Rick Waldron, Anna Gerber, David Resseguie, Emily Rose, Susan Hinton, Sara Gorecki, Bryan Hughes, Andrew Fisher, Julian David Duque, Pawel Szymczykowski, Donovan Buck, Jonathan Beri, Kassandra Perch, Raquel Vélez, Lyza Danger Gardner
Retired
No product available!
The grapple is used for precise operations when replacing SMD and BGA circuits. It allows you to lift small electronic components without using tweezers
Retired
No product available!
Spray CLEANSER PCC 15 with a capacity of 150ml, with a brush is a reliable solution for cleaning printed circuit boards and soldering residues. MICROCHIP
Retired
No product available!
BOB-13752