- Out-of-Stock
AVT3166 C - regulator for rectifier. Assembled set
ID: 563184
Assembled controller for the rectifier. AVT3166 C
Description
Many people are still charging 12V acid batteries with uncomplicated rectifiers containing only a transformer and diodes. Simplicity is an advantage, but the charging parameters are usually far from optimal.
The old proven principle says that a typical car battery should be charged with 1/10 of battery capacity. Charging with a lower current will increase the charging time, but there are no negative effects on the battery. The charging with a much higher current is unfavorable and dangerous.
Project AVT 3166 EdW 11/16
properties
- Charge current adjustment in the range up to approx. 10A
- Automatic charging end
- Signaling of the state of charge by means of LEDs
- Protection against short-circuits and reverse polarity
- It can work as an adapter to the rectifier
- Power supply - transformer 100 ... 200W 16 ... 20 V
- Suitable for charging batteries with a capacity of up to approx. 100 Ah
Included
- Assembled set
563184
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
You might also like
Printed circuit board and programmed controller system for the rectifier. AVT3166 A +
Delivery date unknown
No product available!
AVT kit for self-assembly of the regulator for the rectifier. AVT3166 B
Delivery date unknown
No product available!
Other products in the same category (16)
PCB and pre-programmed system for LED controller controlled by any remote control. AVT3133 A +
Retired
No product available!
AVT kit for self-assembly of LED driver controlled by any remote control. AVT3133 B
Retired
No product available!
Assembled LED lighting controller controlled by any remote control. AVT3133 C
Retired
No product available!
PCB and programmed layout for a 3-axis CNC generator. AVT5422 A +
Retired
No product available!
AVT kit for self-assembly of a 3-axis CNC generator. AVT5422 B
Retired
No product available!
No product available!
USB cable with a length of 100cm, used for data transmission and charging devices with a microUSB connector. A meter is built into the cable plug, allowing the user to estimate the current consumption of the connected device and read the value of the supply voltage
Retired
No product available!
Orange Pi Lite with Quad Core 1.2GHz 512MB DDR3 WiFi Mini PC
Retired
No product available!
Orange Pi Plus 2e is a computer with SoC Alwinner H3 (4 cores, Cortex-A7, Mali400MP2 GPU), has 2 GB of RAM, 16GB of integrated eMMC memory and WiFi 802.11 b / g / n module. There are three USB 2.0 ports, one ethernet port (1 Gigabit), a 40-pin GPIO connector and a micro-SD card slot
Retired
No product available!
No product available!
High quality acrylic computer case for Orange Pi One, transparent
Retired
No product available!
Acrylic computer case for Orange Pi Plus 2. Helps to protect the computer against the dust and mechanical damage. The assembly does not require a glue. Allows easy access to all the computer sockets.
Retired
No product available!
The housing for Orange Pi Plus is transparent, with snaps. The installation does not require the use of glue. The housing is made of high quality plastic. All openings made in the housing allow easy access to every socket built in Orange Pi Plus
Retired
No product available!
Acrylic computer case for Orange Pi PC / PC Plus / PC 2, transparent
Retired
No product available!
PCB and programmed layout for the gigatermometer. AVT3155 A +
Retired
No product available!
AVT kit for self-assembly gigatermometer. AVT3155 B
Retired
No product available!
Assembled controller for the rectifier. AVT3166 C