- Out-of-Stock

The Multi-Touch Display Shield is a gorgeous 2.8“ touchscreen display with a powerful on-board microcontroller that performs graphics processing tasks. The display is a capacitive touchscreen with QVGA resolution (320×240) and 2 finger multi-touch support. Digilent 410-317
The Multi-Touch Display Shield is a gorgeous 2.8“ touchscreen display with a powerful on-board microcontroller that performs graphics processing tasks. The display is a capacitive touchscreen with QVGA resolution (320×240) and 2 finger multi-touch support.
The most compelling aspect of the Multi-Touch Display Shield is the programming experience provided by its Multi-Touch Display System (MTDS) Firmware and the associated libraries. These allow you to design sleek, stylish user interfaces quickly and with very little code. The timing dependent tasks are handled by the firmware, so integrating the display into existing projects is also a snap. Some of the key functionality provided by the libraries include the ability to draw basic shapes and text, draw images stored on microSD with binary transparency, draw buttons and easily check if they have been pressed, and check the status and location of the user's two fingers. The libraries are supported in Arduino IDE and Xilinx SDK, and have been tested with Arduino, chipKIT, and Arty host boards.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
Pmod MTDS is a module with a 2.8-inch LCD display. It has a resolution of 320x240 pixels. It has touch support (capacitive, 2 point). Digilent 410-341
No product available!
No product available!
EXTREME heat shrink tubing for electrical and mechanical insulation, diameter against shrinkage 5.0 mm; diameter after shrinkage 1.5 mm, a set of 10 pieces with a length of 1 meter
No product available!
Freescale starter kit with Kinetis KE04Z microcontroller (Cortex-M0 +, 5V power supply ), integrated with the OpenSDA debugger-programmer, capacitive switch, LED-RGB and MEMS 3D accelerometer. Arduino-compatible outputs.
No product available!
No product available!
HK Turnigy TrackStar Waterproof 1/10 Brushless Power System 4000KV/80A (25138)
No product available!
No product available!
No product available!
No product available!
No product available!
Alan Katritzky, Christopher Ramsden, Eric Scriven, Richard Taylor
No product available!
Waveshare WIFI232 Eval Kit is an evaluation board WIFI501 with WIFI232-B module. The board has a USB - UART converter, a reload button, an RJ45 ethernet interface connector and an RS485 interface connector. Waveshare WIFI232 Eval Kit
No product available!
No product available!
TSL2561 luminosity sensor is an advanced digital light sensor, ideal for use in a wide range of light situations. Compared to low cost CdS cells, this sensor is more precise, allowing for exact lux calculations and can be configured for different gain/timing ranges to detect light ranges from up to 0.1 - 40,000+ Lux on the fly. Adafruit 439
No product available!
No product available!
No product available!
No product available!
The Multi-Touch Display Shield is a gorgeous 2.8“ touchscreen display with a powerful on-board microcontroller that performs graphics processing tasks. The display is a capacitive touchscreen with QVGA resolution (320×240) and 2 finger multi-touch support. Digilent 410-317