- Out-of-Stock
FireBeetle Covers DC Motor & Stepper Driver - 4-channel DC motor driver for FireBeetle
ID: 569868
Module with 4-channel DC motor driver (2 x TB6612FNG) designed for FireBeetle boards. It communicates via the I2C interface. DFRobot DFR0508
Description
The module with the controller of DC motors designed for FireBeetle boards. It is based on two TB6612FNG chips and the STM8S105 microcontroller, which controls the H bridges and communicates via the I2C interface. It allows you to control four DC motors with a voltage in the range from 2.5 to 13.5 V, and each channel can take a current of 1.2 A (temporary 3.2 A). The module can also control the movement of two stepper motors or 4 servos. Motors and power supply to drives are connected via screw connections. There is also a 4x3-pin connector for connecting servos. The driver allows you to reduce the number of pins needed to control the drives to a minimum. It can be used in mobile robots and home automation. Full documentation is available on the product page.
Features
- 4-channel support for DC motors
- Support for 2 channels of four-wire stepper motors
- Support for 4 channels of servo drive
- Refresh rate up to 1000 Hz
- Equipped with a LED indicator
- STM8S105 microcontroller
- Operating voltage: 3.3 to 5V
- Working voltage: 30mA
- Engine Drive System: TB6612FNG
- Motor voltage: 4-12V
- Output current: 1.2 A single-channel continuous driving current
- Starting / peak current: 2 A (continuous pulse) / 3.2A (single pulse)
- Communication port: I2C
- I2C address: 0x18
- Dimensions: 58 x 29 mm
Kit contains
- FireBeetle Covers DC Motor & Stepper Driver module
- 2 x 18-pin goldpin male connector
- 2 x 18-pin goldpin female connector
569868
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The low-power consumption micro-controller intentionally designed for Internet of Things (IoT) projects. The board integrates a Dual-Core ESP-WROOM-32 module, which supports MCU and Wi-Fi &Bluetooth dual-mode communication. DFR0478
zł49.19
24h
Available quantity: 5
Available
Plate for applications in the area of Internet of Things (IoT). The module was based on the ESP8266 system, which integrates WiFi, TCP / IP communication, 32-bit MCU, 10-bit ADC and many interfaces such as HSPI, UART, PWM, I2C and I2S. DFrobot DFR0489
zł37.75
24h
Available quantity: 2
Available
GPIO expansion module designed for FireBeetle boards. It is equipped with a set of connectors to facilitate the connection of sensors. DFRobot DFR0483
zł36.73
Delivery date unknown
No product available!
Board for applications in the area of the Internet of Things (IoT). The module is based on the ESP-WROOM-32E system with 240 MHz clock, equipped with 4 MB Flash and 520 KB SRAM, as well as WiFi and Bluetooth communication. DFRobot DFR0654
zł48.89
24h
Available quantity: 8
Available
Board for applications in the area of the Internet of Things (IoT). The module is based on the ESP-WROOM-32E system with 240 MHz clock, equipped with 4 MB Flash and 520 KB SRAM, as well as WiFi and Bluetooth communication. DFrobot DFR0654-F
zł53.96
24h
Available quantity: 3
Available
Other products in the same category (16)
Kit: MAXimator, MAXimator Expander, ZL32PRG - USB Blaster PRO
Retired
No product available!
Power Supply 2.5A 5.1V for Raspberry Pi 3 model B - STONTRONICS T5875DV
Retired
No product available!
MYD-JA5D44 Development Board is a complete educational platform. Its heart is the MYIR MYC-JA5D44 module, which was equipped with the Atmel SAMA5D44 processor based on Cortex-A5 cores. The processor can work at a maximum frequency of 600 MHz. Min. RS232, RS485 connectors, HDMI connector, 3.5 mm Jack Audio inputs, microSD memory card slot, 10/100 Mbps Ethernet slot and many more.
Retired
No product available!
The Raspberry Pi GPIO Triple Expansion Board converts the single GPIO headers on your Raspberry Pi into three parts. DFR0385
Retired
No product available!
Flex Cable for Raspberry Pi Camera - 300mm / 12". Adafruit 1648
Retired
No product available!
Comes with a 6"x6" (152mm x 152mm) square of Pyralux. It\'s ED-Y type copper at 35um (1 oz/ft2) and has a polymide of 25um (1 mil). The thick copper layer means it can carry a lot of current, and its trivial to solder to it. Adafruit 1894
Retired
No product available!
Patchcord UTP 5E Ethernet cable with a length of 50 cm - gray, with 2xRJ45 connectors
Retired
No product available!
Patchcord UTP 5E Ethernet cable with a length of 50 cm - blue, with 2xRJ45 connectors
Retired
No product available!
Patchcord UTP 5E Ethernet cable with a length of 1.5 m - black, with 2xRJ45 connectors
Retired
No product available!
Patchcord UTP 5E Ethernet cable with a length of 3 m - black, with 2xRJ45 connectors
Retired
No product available!
Patchcord UTP 5E Ethernet cable with a length of 5 m - blue, with 2xRJ45 connectors
Retired
No product available!
Patchcord UTP 5E Ethernet cable with a length of 5 m - gray, with 2xRJ45 connectors
Retired
No product available!
The board gives the possibility to significantly extend the functionality of the STM32F407G-DISC1 development kit. The plate contains, among others memory card slot (microSD), Ethernet socket and connectors that can be used to attach SMT32F4DIS modules to the board
Delivery date unknown
No product available!
Camera board for the STM32F407G-DISC1 set. It allows you to capture an image with a resolution of 1280 x 1024 pixels (1.3MP). The set includes a flexible cable that allows the camera to be connected to the STM32F4DIS-BB expansion board
Retired
No product available!
The MyoWare Muscle Sensor is now designed to be wearable allowing you to attach biomedical sensor pads directly to the board itself. DEV-13687
Retired
No product available!
No product available!
Module with 4-channel DC motor driver (2 x TB6612FNG) designed for FireBeetle boards. It communicates via the I2C interface. DFRobot DFR0508