- Out-of-Stock
AVT3225 A + - universal stepper motor controller. PCB and programmed layout
ID: 572253
Printed circuit board and programmed circuit for universal stepper motor controller. AVT3225 A +
Description
The controller allows for the construction of advanced mock-ups, the development of machines and tools such as milling machines or drills, but it can also be useful in photography for the construction of a drive for the shooting of timelaps and 360º images.
The engine controller enables smooth regulation of the speed and direction of rotation of the bipolar (4-wire) and unipolar (5-, 6- or 8-wire) stepper motors with one potentiometer. The range of rotation speed changes of the motor axis has been divided into two sub-ranges 1 ... 10 or 7 ... 100 cycles per second.
Project AVT 3225 EdW 07/18
properties
- Board dimensions: 83x33 mm
Included
- PCB board and programmed layout
572253
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Cable with a length of 150 mm, on one side terminated with a Qwiic connector, and on the other side with single female goldpin connectors. It allows you to connect Qwiic modules, e.g. with development board. SparkFun CAB-14988
Retired
No product available!
Extension module for Raspberry Pi designed to build the user interface. It is equipped with a 2.4-inch TFT LCD display, microphones, speaker, buttons, joystick and RGB LEDs. SparkFun DEV-16653
Retired
No product available!
Adapter board from SODIMM200-2.5 to 2.54mm connectors
Retired
No product available!
The expansion module to support two cameras is designed for Raspberry Pi minicomputers. The board allows you to connect two cameras via CSI connectors to one minicomputer connector. ArduCAM B016601
Retired
No product available!
Evaluation kit with LittleBee GW1N-1 FPGA chip. Offers 1152 LUTs and 864 Flip-Flops (FF). The board has an FPC connector for the display and a USB type C. Sipeed Lichee Tang Nano
Retired
No product available!
Video splitter for connecting one input device to 2 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0002
Retired
No product available!
Video splitter for connecting one input device to 4 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0004
Retired
No product available!
Video splitter for connecting one input device to 8 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0008
Retired
No product available!
Video switch that allows you to connect 5 input devices to one HDMI receiver. The input signal can be selected using a button on the casing or the included remote control. Lanberg SWV-HDMI-0005
Retired
No product available!
A set of 8 knives, including 4 knives with broken blades and 4 special-purpose knives. Vorel 76280
Retired
No product available!
Module with an analog temperature and humidity sensor based on the SHT10 system. It is characterized by high reliability and stability with low energy consumption. It is compatible with 3.3V and 5V controllers. DFRobot DFR0066
Retired
No product available!
Module with a CCS811 air quality sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C interface (Gravity connector). DFRobot SEN0318
Retired
No product available!
Module with a gesture and touch sensor. It recognizes 7 types of gestures and has 5 touch buttons. It is supplied with a voltage ranging from 3.3 V to 5 V and communicates via UART. DFRobot SEN0285
Retired
No product available!
Module with a 3-axis analog MMA7361 accelerometer. There are 3 Gravity connectors on the board (for each axis). The operating range of the sensor can be configured using a DIP switch. DFRobot DFR0143
Retired
No product available!
Module with a UV ultraviolet light sensor VEML6075. Enables measurement of the level of UVA (350-375 nm) and UVB (315-340 nm) radiation. It communicates via the I2C bus. DFRobot SEN0303
Retired
No product available!
The I2C-GPIO converter module is powered with the voltage of 5 V. It allows you to extend the number of digital pins of the Arduino-compatible board with an additional 16 IO pins. DFRobot DFR0013
Retired
No product available!
Printed circuit board and programmed circuit for universal stepper motor controller. AVT3225 A +