• Out-of-Stock
PYNQ-Z1 Accessory Kit - EDU
search
  • PYNQ-Z1 Accessory Kit - EDU
  • PYNQ-Z1 + Accessory Kit - EDU
ID: 576207

Development board FPGA PYNQ-Z1 and accessor set. Includes base plate, power supply, cables and SD card with system image for PYNQ-Z1. Academic version. Digilent 240-114-1

Retired
Kamami is the official distributor of Digilent FPGA kits, modules and measurement tools. All products of this brand in our offer are original and come directly from the manufacturer.
 

Free shipping

free shipping in Poland for all orders over 500 PLN

 

Same day shipping

If your payment will be credited to our account by 11:00

 

14 days for return

Each consumer can return the purchased goods within 14 days

ATTENTION! This product is for academic recipients (students and academic teachers) only!

After the ordering, please send us by e-mail the data listed below:

  • the name and last name
  • position (student, teacher)
  • e-mail (with the University domain)
  • University name
  • Facultie / Section
  • University address
  • University phone no.

Description

Development board FPGA PYNQ-Z1 and accessor set. Includes base plate, power supply, cables and SD card with image for PYNQ-Z1.

PYNQ-Z1 is a programmable FPGA board for embedded systems that natively supports multimedia using on-board audio and video interfaces. The board has been designed to easily expand its capabilities with the help of Pmod modules, Arduino shields, Grove extensions, as well as using shared GPIO ports. The capabilities of the PYNQ-Z1 set can also be expanded using USB devices - such as Wi-Fi cards, Bluetooth modules or cameras.

The product is also available in the academic offer (EDU) at a reduced price: PYNQ-Z1 + Accessory Kit - EDU

Features

  • ZYNQ XC7Z020-1CLG400C:
    • 650MHz dual-core Cortex-A9 processor
    • DDR3 memory controller with 8 DMA channels and 4 high performance AXI3 slave ports
    • High-bandwidth peripheral controllers: 1G Ethernet, USB 2.0, SDIO
    • Low-bandwidth peripheral controller: SPI, UART, CAN, I2C
    • Programmable from JTAG, Quad-SPI flash, and microSD card
    • Artix-7 family programmable logic
      • 13,300 logic slices, each with four 6-input LUTs and 8 flip-flops
      • 630 KB of fast block RAM
      • 4 clock management tiles, each with a phase-locked loop (PLL) and mixed-mode clock manager (MMCM)
      • 220 DSP slices
      • On-chip analog-to-digital converter (XADC)
  • Memory:
    • 512MB DDR3 with 16-bit bus @ 1050Mbps
    • 16MB Quad-SPI Flash with factory programmed globally unique identifier (48-bit EUI-48/64™ compatible).
    • MicroSD slot
  • Power:
    • Powered from USB or any 7V-15V source (see recommended products)
    • USB and Ethernet:
    • USB-JTAG Programming circuitry
    • USB-UART bridge
    • USB OTG PHY (supports host only)
    • Gigabit Ethernet PHY
  • Audio and Video:
    • Electret microphone with pulse density modulated (PDM) output
    • 3.5mm mono audio output jack, pulse-width modulated (PWM) format
    • HDMI sink port (input)
    • HDMI source port (output)
  • Switches, push-buttons, and LEDs:
    • 4 push-buttons
    • 2 slide switches
    • 4 LEDs
    • 2 RGB LEDs
  • Expansion Connectors:
    • Two standard Pmod ports
    • 16 Total FPGA I/O
  • Arduino/chipKIT Shield connector:
    • 49 Total FPGA I/O
    • 6 Single-ended 0-3.3V Analog inputs to XADC
    • 4 Differential 0-1.0V Analog inputs to XADC

Kit contains

  • Development board PYNQ-Z1
  • Micro USB cable
  • Ethernet cable
  • MicroSD card with pre-loaded PYNQ-Z1 boot image
  • 12 V/3 A power supply
576207

You might also like

Other products in the same category (16)