.png)
- Out-of-Stock
FRDM-K32L2B3 - starter kit with Freescale Kinetis K32 L2B microcontroller
ID: 580206
Starter kit with the Kinetis K32 L2B microcontroller, integrated with the OpenSDA programmer-debugger, LCD display, accelerometer and MEMS magnetometer and USB connector. Conclusions compatible with Arduino. NXP FRDM-K32L2B3
Description
FRDM-K32L2B3 is a starter kit with K32L2B31VLH0A microcontroller. The board has an LCD segment display, a 6-axis IMU sensor (accelerometer and magnetometer) and a connector with an FS USB interface. The set can be powered by 5 V and has been equipped with a connector compatible with Arduino Uno Rev3, thanks to which the user can extend the possibilities with additional sensors and modules. The kit is an excellent tool for the implementation of projects using motion sensors. The manufacturer has prepared support in the form of software, examples and quick start instructions.
Features
- K32L2B31VLH0A MCU microcontroller (48 MHz, 256 kB FLash, 32 kB SRAM)
- I/O connectors with led out pins of the microcontroller
- Built-in debugger: OpenSDA with virtual serial port
- FXOS8700CQ 6-axis IMU sensor (accelerometer and magnetometer)
- Reset button, two user buttons
- LED lights
- LCD segment display
- The connector is compatible with Arduino Uno Rev3
580206
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
You might also like
Cable with USB typ A and microUSB typ B connectors, cable length 1 m. LANBERG CCP-MUSB2-AMBM-W-1M
zł2.87
24h
Available quantity: 30
Available
Cable with USB typ A and microUSB typ B connectors, cable length 1.8 m. LANBERG CA-USBM-10CC-0018-BK
zł4.00
24h
Available quantity: 8
Available
Cable with USB typ A and microUSB typ B connectors, cable length 1.8 m. LANBERG CA-USBM-10CC-0018-W
zł3.39
24h
Available quantity: 16
Available
Other products in the same category (16)
PCB and programmed layout for programmable LED driver. AVT1881 A +
Retired
No product available!
AVT kit for self-assembly of the programmable LED driver. AVT1881 B
Retired
No product available!
AVT kit for self-assembly of LED strip driver with time switch. AVT1867 B
Retired
No product available!
Assembled LED strip driver with timer. AVT1867 C
Retired
No product available!
PCB and pre-programmed system for LED controller controlled by any remote control. AVT3133 A +
Retired
No product available!
AVT kit for self-assembly of LED driver controlled by any remote control. AVT3133 B
Retired
No product available!
Assembled LED lighting controller controlled by any remote control. AVT3133 C
Retired
No product available!
PCB and programmed layout for a 3-axis CNC generator. AVT5422 A +
Retired
No product available!
AVT kit for self-assembly of a 3-axis CNC generator. AVT5422 B
Retired
No product available!
No product available!
USB cable with a length of 100cm, used for data transmission and charging devices with a microUSB connector. A meter is built into the cable plug, allowing the user to estimate the current consumption of the connected device and read the value of the supply voltage
Retired
No product available!
Orange Pi Lite with Quad Core 1.2GHz 512MB DDR3 WiFi Mini PC
Retired
No product available!
Orange Pi Plus 2e is a computer with SoC Alwinner H3 (4 cores, Cortex-A7, Mali400MP2 GPU), has 2 GB of RAM, 16GB of integrated eMMC memory and WiFi 802.11 b / g / n module. There are three USB 2.0 ports, one ethernet port (1 Gigabit), a 40-pin GPIO connector and a micro-SD card slot
Retired
No product available!
No product available!
High quality acrylic computer case for Orange Pi One, transparent
Retired
No product available!
Acrylic computer case for Orange Pi Plus 2. Helps to protect the computer against the dust and mechanical damage. The assembly does not require a glue. Allows easy access to all the computer sockets.
Retired
No product available!
Starter kit with the Kinetis K32 L2B microcontroller, integrated with the OpenSDA programmer-debugger, LCD display, accelerometer and MEMS magnetometer and USB connector. Conclusions compatible with Arduino. NXP FRDM-K32L2B3