- Out-of-Stock
Auvidea 70511 - HDMI to CSI-2 converter module
ID: 580480
HDMI to CSI-2 bridge module based on TC358840 chip. It has a 22-pin FPC connector with a pitch of 0.5 mm and an audio connector. The input signal is supplied through the HDMI connector. Auvidea 70511
Description
HDMI to CSI-2 bridge module based on TC358840 chip. It has a 22-pin FPC connector with a pitch of 0.5 mm and an audio connector. The input signal is supplied through the HDMI connector. The TC358840 chip is a bridge that converts a high definition HDMI stream (above 4 Gb/s) to MIPI CSI-2 video. The module will be used in the case of projects using application processors that have only a CSI-2 video connector.
Features
- Toshiba TC358840 chip
- HDMI input:
- HDMI 1.4b
- Video formats support (up to 4K × 2K / 30fps), maximum 24 bps (bit per pixel)
- Maximum HDMI clock speed: 297 MHz
- Supports audio
- Sent by ACR packet
- 3D support
- Support HDCP1.4 decryption (optional)
- EDID Support Release A Revision 1
- CSI-2 output:
- Compliant with MIPI CSI-2
- CSI-2 dual links (CSI0 and CSI1), each link supports 4 1Gbps data lines
- Single CSI-2 link, maximum horizontal pixel width: 2558 pixels (24 bits per pixel), 3411 pixels (16 bits per pixel)
- HDMI InfoFrame data can be transferred via MIPI
- Audio output:
- Up to four I2S data lines
- The maximum supported audio sampling rate is 192 kHz at 8 channels
- Supports 16, 18, 20 or 24-bit data
- Only supports master clock output
- It only supports 32-bit timeslots
- Audio Over Sampling Clock Output (256fs)
- I2S or TDM audio interface available
- The digital audio interface supports HBR audio stream split into 4 I2S lines if the bandwidth is greater than 12MHz
580480
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
HDMI cable compliant with the HDMI High Speed with Ethernet specification, allows you transmit a 4k resolution image at 30 Hz, 0.5m cable length. LANBERG
zł4.80
24h
Available quantity: 14
Available
HDMI cable compliant with the HDMI High Speed with Ethernet specification, allows you transmit a 4k resolution image at 30 Hz, 1m cable length. LANBERG
zł5.24
24h
Available quantity: 12
Available
HDMI cable compliant with the HDMI High Speed with Ethernet specification, allows you transmit a 4k resolution image at 30 Hz, 1,8m cable length. LANBERG z27510
zł6.69
24h
Available quantity: 6
Available
Other products in the same category (16)
Extension module for Raspberry Pi. The board has 7 RGB LEDs, four 14-segment displays, three single-color LEDs, as well as three touch buttons, a BMP280 sensor and a buzzer. Pimoroni PIM242
Retired
No product available!
No product available!
No product available!
No product available!
DipPLD module with XC2C256 (CoolRunner-II from Xilinx)
Retired
No product available!
HALLOTRON DC CURRENT INDICATOR - PRINTED PLUG AND PROGRAMMED SYSTEM
Delivery date unknown
No product available!
NORT16 is a workshop organizer made of high quality plastic, transparent, closed with latches, with a solid handle for convenient transport. It has the ability to regulate the size and number of compartments
Retired
No product available!
Module with Tegra X1 SoC system containing four 64-bit ARM Cortex A57 cores and a Maxwell graphic layout consisting of 256 cores supporting CUDA technology. NVIDIA Jetson TX1
Retired
No product available!
Industrial DTU 4G module with Qualcomm SIM7600E-H chip. It allows you to connect industrial modules with serial communication via RS232, RS485 or TTL interfaces with 4G networks. Waveshare SIM7600E-H 4G DTU (EU)
Retired
No product available!
No product available!
No product available!
The eMMC 5.1 flash memory module for Hardkernel Odroid XU4 computers. 128GB capacity, Android operating system installed. The set includes a microSD adapter. Hardkernel
Retired
No product available!
No product available!
No product available!
No product available!
3D printer with automatic table leveling and printing resume function. Equipped with a double Z axis and a filament sensor. It offers a large working space of 300 x 300 x 400 mm and uses a fully metal hotend. It allows printing at a speed of 300mm/s, which translates into 30% faster printing compared to previous versions of Sidewinder printers. Artillery Sidewinder X3 Plus
Retired
No product available!
HDMI to CSI-2 bridge module based on TC358840 chip. It has a 22-pin FPC connector with a pitch of 0.5 mm and an audio connector. The input signal is supplied through the HDMI connector. Auvidea 70511