- Out-of-Stock
Filament ROSA3D PET-G CarbonLook 1.75mm Black
ID: 587777
5907753130716
ROSA3D filament made of high-quality PET-G granules with a small addition of carbon fibers. 0.5 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PET-G CarbonLook
Description
1.75 mm PET-G filament for 3D printing by ROSA3D. 0.5 kg of filament is wound on the spool. The recommended printing temperature is in the range from 220°C to 260°C, and the temperature of the bed during printing in the range of 60°C - 80°C.
Rosa3D is a Polish manufacturer of filaments intended for both hobby and industrial printing. Thanks to many years of experience and modern machinery, the company is able to provide good quality and accuracy of the diameter and roundness of the filament. The PET-G CarbonLook filament was designed for prints where the visual effect of the object is more important than its industrial use. It will be used in the creation of prototypes and large-format prints.
The small addition of carbon fibers used in the material results in a printout with a satin surface and almost invisible layers, with only a slight stiffening of the material. An additional advantage is the possibility of obtaining a slight transparency of the material in prints with very thin walls. Printing with PET-G CarbonLook is characterized by a low level of threading and excellent adhesion between the layers. It is just as easy to achieve fascinating results as with the PET-G Standard filament. The material shows no shrinkage and does not require a closed chamber. Due to the low content of carbon fibers in the material, the abrasion of the filament is lower than in the PETG+CF material, which translates into less wear of the printing nozzle.
Features
- Color: Black
- Diameter: 1.75 mm
- Diameter tolerance: +/- 0.05mm
- Oval tolerance: +/- 0.02mm
- Printing temperature: 220°C to 260°C
- Bed temperature: 60°C to 80°C
- Density 1.29 g/cm3
- Odorless smell
- Elongation at tensile 5.5%
- Tensile strength (to break) 45 MPa
- Tensile modulus is 2980 MPa
- Impact strength according to the Izod method with a notch of 4.7 kJ/m2
- Vicat softening point 78°C
- Net weight: 0.5 kg
587777
Data sheet
- Rodzaj filamentu
- PET-G
- Ilość filamentu
- 0,5 kg
- Diameter
- 1,75 mm
- Colour
- Black
You might also like
Easy-to-use and intuitive 3D printer with touch display and USB, WiFi and intelligent door support. The printer is fully assembled and ready to use. Flashforge Inventor IIS
Regular pricezł3,704.21zł1,999.00
24h
Available quantity: 1
Available
Knife designed for trimming and processing of prints from a 3D printer. It consists of a plastic handle and a replaceable, curved blade made of steel
zł9.40
Delivery date unknown
No product available!
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Spray 400ml
zł52.90
24h
Available quantity: 22
Available
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Pen 90ml
zł54.46
24h
Available quantity: 261
Available
ROSA3D filament made of high-quality PET-G granules with the addition of carbon fibers. 3 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PET-G + CF
Delivery date unknown
No product available!
Other products in the same category (16)
CryptoShield is a dedicated security peripheral for the Arduino. This shield adds specialized ICs that perform various cryptographic operations which will allow you to add a hardware security layer to your Arduino project. It also is a nice device for those performing embedded security research. DEV-13183
Retired
No product available!
No product available!
Banana Pi R1 acrylic clear case. The case needs to be assembled by yourself
Retired
No product available!
The housing for the Banner PI G1 Debugger made of transparent plastic. Housing for self-assembly
Retired
No product available!
The I2C electric level conversion module is specifically designed for Banana Pi. The module converts the 3.3V of I2C electric level to 5V level or converts 5V to 3.3V
Retired
No product available!
BPI AD/DA extend module with the PCF8591 single-chip, single-supply low-power 8-bit CMOS data acquisition device with four analog inputs, one analog output and a serial I2C-bus interface
Retired
No product available!
No product available!
5dB antenna for the Banana Pi R1 router in the version with 300Mps wifi and five LAN 100/1000 ports.
Retired
No product available!
STM32F103 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC3200 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC2530 and CC2540 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
It is a standard audio-video cable, which can be successfully used to connect Banana Pi M1 or Raspberry Pi 1 model B and A. Cable length is 98 cm, has two ends of the chinch type.
Retired
No product available!
COM-11964 Button a white economy grade 100mm diameter (outside diameter) dome illuminated push button comes with an LED, securing nut and a long life horizontal microswitch.
Retired
No product available!
Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). The version is assembled. Adafruit 2029
Retired
No product available!
T-Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). Goldpin connectors are included, for self-assembly. Adafruit 1989
Retired
No product available!
FPC tape length 250 mm, 50 lines, pitch 0.5 mm. Adafruit 1682
Retired
No product available!
ROSA3D filament made of high-quality PET-G granules with a small addition of carbon fibers. 0.5 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PET-G CarbonLook